Service Manual
Table Of Contents
- Whirlpool & Maytag 27" Front-Load Gas & Electric Dryers
- Table of Contents
- Section 1: General Information
- Section 2: Diagnostics & Troubleshooting
- Section 3: Component Testing
- Testing - Safety Information
- Component Locations - Whirlpool
- Wiring Diagram - Whirlpool Electric
- Wiring Diagram - Whirlpool Gas
- Wiring Diagram - Maytag Electric
- Wiring Diagram - Maytag Gas
- Component Testing
- TEST #1: ACU Power Check
- TEST #2: Supply Connections
- TEST #3: Motor Circuit
- TEST #4: Heat System
- TEST #4a: Thermistors
- TEST #4b: Thermal Fuse
- TEST #4c: Thermal Cut-Off
- TEST #4d: Gas Valve (Gas Dryer)
- TEST #5: Moisture Sensor
- TEST #6: Buttons & Indicators
- TEST #7: Door Switch
- TEST #8: Drum LED
- TEST #9: Water Valve
- Section 4: Component Access
- Component Locations - Whirlpool
- Door Reversal - Round Shaped Doors
- Door Reversal - Square Shaped Doors
- Removing the Top Panel & Console/HMI
- Removing the Appliance Control Unit (ACU)
- Removing the Front Panel & Door Switch
- Removing the Drum Light & Moisture Sensor
- Removing the Belt, Drum, and Rollers
- Removing the Drive Motor
- Removing the Thermal Fuse & Outlet Thermistor
- Removing the Heater, High Limit Thermostat & Thermal Cutoff
- Removing the Ignitor, Flame Sensor, High-Limit Thermostat and Thermal Cutoff (Gas Models)
- Removing the Gas Burner Assembly Coils (Gas Models)
- Removing the Rear Panel
- Removing the Water Valve
- Section 5: Connectivity
- Product Specifications & Warranty Info
2-10
n
Whirlpool & Maytag Front-Load Dryers
DIAGNOSTICS & TROUBLESHOOTING
Component Activation
To enter the Service Test Mode from the Component
Acvaon menu, press “START” to begin the diagnosc test
(see Figure 3). Perform the “Acons” listed in the chart below
to advance through each step in the Service Test Mode.
Figure 3
Whirlpool LCD in Door Diagnostics
SERVICE DIAGNOSTIC MODE TESTS (Connued)
Step Acon Component Human-Machine Interface Response
1 User enters "Component Acvaon"
through Service Diagnoscs
Display shows "START - O"
2 Touch START to begin “Quick Service
Cycle” test.
"Motor On
Water Valve On"
"Display shows ""DRYER - FACTORY TESTING""
Model Number:
Serial Number:
""Advance Phase"" buon prompt"
3 Touching the "Advance Phase"
buon begins the heater test.
"Motor On
Water Valve On
Heater On"
"Display shows ""DRYER - FACTORY TESTING""
Test: Heater
""Advance Phase"" buon prompt"
4 Touching the "Advance Phase"
buon stops the heater test.
"Motor On
Water Valve On
Heater O"
Display shows "START - On"
5 Open door to test the door switch. "Motor O
Water Valve O
Door Switch"
"Display shows ""DRYER - FACTORY TESTING""
Test: Door Switch
If the Door Switch FAILED, the diagnosc test will not
connue or meout.
If the Door Switch test PASSED, the message
advances to:
Test: Moisture Sensor"
6 Touch your ngers across the two
front moisture sensor strips
Moisture Sensor "Display shows ""DRYER - FACTORY TESTING""
Test: Moisture Sensor
If the Moisture Sensor FAILED, the diagnosc test will
not connue or meout.
If the Moisture Sensor test PASSED, the message
advances to:
Overall Status: PASSED/FAILED"
7 "If all tests PASS = Overall Status: PASSED
If any tests FAIL = Overall Status: FAILED"
Service Test Mode
The Service Test Mode will run as described in the table below. NOTE: The drum must be empty during this test.
NOTE: If, at any point, the user presses the POWER buon
during the Service Test Mode, the dryer exits to standby mode.
PERFORM ALL TESTS: Complete all tests listed in the Service
Test Mode chart below. At the compleon of all the tests, the
Human-Machine Interface (HMI) will respond an overall status
of PASSED or FAILED.
Exit Procedure
When the test cycle is complete, press the POWER buon to
exit Service Test Mode and return to standby mode.
NOTE: The steam valve will be acvated during steps 1 - 4. Wipe up any excess water in drum aer diagnosc test has completed.