Service Manual

COMPONENT ACCESS
Whirlpool & Maytag Front-Load Dryers
n
4-5
Door Reversal — Round-Shaped Doors (continued)
8. Flip over the inner door to the le. Using a T20®
screwdriver, reinstall the hinge assembly on the opposite
side from which it was removed.
26
8.
Reinstall hinge assembly on opposite side
Flip over the inner door to the left. Using a T20
®
screwdriver,
reinstall the hinge assembly on the opposite side from which
it was removed.
DOORS WITH ELECTRICAL WIRING:
9.
Remove rotating assembly
Lift off inner door assembly. Using a Phillips screwdriver,
remove the two screws securing the rotating assembly
to the door.
10. Reposition rotating assembly
and tubing
Reposition rotating assembly and tubing 180 ° to opposite side
of the door.
11. Rotate assembly bottom and fasten
in place
Rotate bottom of assembly 180° towards you and secure
assembly with the two screws removed earlier, using a Phillips
screwdriver. Press tubing into indents.
IMPORTANT: Make sure to swing hinge down in front of
rotating assembly (see Step 12).
Press tubing
into indents.
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 8 - Reinstall hinge assembly on opposite side.
DOORS WITH ELECTRICAL WIRING:
9. Li o inner door assembly. Using a Phillips screwdriver,
remove the two screws securing the rotang assembly to
the door.
26
8.
Reinstall hinge assembly on opposite side
Flip over the inner door to the left. Using a T20
®
screwdriver,
reinstall the hinge assembly on the opposite side from which
it was removed.
DOORS WITH ELECTRICAL WIRING:
9. Remove rotating assembly
Lift off inner door assembly. Using a Phillips screwdriver,
remove the two screws securing the rotating assembly
to the door.
10. Reposition rotating assembly
and tubing
Reposition rotating assembly and tubing 180 ° to opposite side
of the door.
11. Rotate assembly bottom and fasten
in place
Rotate bottom of assembly 180° towards you and secure
assembly with the two screws removed earlier, using a Phillips
screwdriver. Press tubing into indents.
IMPORTANT: Make sure to swing hinge down in front of
rotating assembly (see Step 12).
Press tubing
into indents.
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 9 - Remove rotating assembly.
10. Reposion rotang assembly and tubing 180° to opposite
side of the door.
26
8. Reinstall hinge assembly on opposite side
Flip over the inner door to the left. Using a T20
®
screwdriver,
reinstall the hinge assembly on the opposite side from which
it was removed.
DOORS WITH ELECTRICAL WIRING:
9. Remove rotating assembly
Lift off inner door assembly. Using a Phillips screwdriver,
remove the two screws securing the rotating assembly
to the door.
10. Reposition rotating assembly
and tubing
Reposition rotating assembly and tubing 180 ° to opposite side
of the door.
11. Rotate assembly bottom and fasten
in place
Rotate bottom of assembly 180° towards you and secure
assembly with the two screws removed earlier, using a Phillips
screwdriver. Press tubing into indents.
IMPORTANT: Make sure to swing hinge down in front of
rotating assembly (see Step 12).
Press tubing
into indents.
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 10 - Reposition rotating assembly and tubing.
11. Rotate boom of assembly 180° towards you and secure
assembly with the two screws removed earlier, using a
Phillips screwdriver. Press tubing into indents.
IMPORTANT: Make sure to swing hinge down in front of
rotang assembly (see Step 12).
26
8. Reinstall hinge assembly on opposite side
Flip over the inner door to the left. Using a T20
®
screwdriver,
reinstall the hinge assembly on the opposite side from which
it was removed.
DOORS WITH ELECTRICAL WIRING:
9. Remove rotating assembly
Lift off inner door assembly. Using a Phillips screwdriver,
remove the two screws securing the rotating assembly
to the door.
10. Reposition rotating assembly
and tubing
Reposition rotating assembly and tubing 180 ° to opposite side
of the door.
11. Rotate assembly bottom and fasten
in place
Rotate bottom of assembly 180° towards you and secure
assembly with the two screws removed earlier, using a Phillips
screwdriver. Press tubing into indents.
IMPORTANT: Make sure to swing hinge down in front of
rotating assembly (see Step 12).
Press tubing
into indents.
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 11 - Rotate assembly bottom and fasten in place.