Service Manual

4-6
n
Whirlpool & Maytag Front-Load Dryers
COMPONENT ACCESS
Door Reversal — Round-Shaped Doors (continued)
ALL DOORS:
12. Posion the door with the inside of the door facing
up. Using a Phillips screwdriver, reinstall the 10 screws
removed earlier, securing the inner door to the outer
door.
27
12. Reinstall inner door assembly
Position the door with the inside of the door facing up. Using
a Phillips screwdriver, reinstall the 10 screws removed earlier,
securing the inner door to the outer door.
13. Reinstall door on dryer
Doors with electrical wiring: Pull the wire through the front
panel opening before reinstalling the door.
Insert the tabs on the hinge into the mounting slot and slide
down to engage the top tab. Secure in place with the
four T25
®
screws removed earlier.
Bottom
of door
14. Reconnect wiring
Plug in wire. Using a Phillips screwdriver, secure the rotating
assembly to the hinge with the screw removed earlier.
ALL DOORS: DOORS WITH ELECTRICAL WIRING:
Swing
down
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 12 - Reinstall inner door assembly.
13. Doors with electrical wiring: Pull the wire through the
front panel opening before reinstalling the door. Insert the
tabs on the hinge into the mounng slot and slide down
to engage the top tab. Secure in place with the four T25®
screws removed earlier.
27
12. Reinstall inner door assembly
Position the door with the inside of the door facing up. Using
a Phillips screwdriver, reinstall the 10 screws removed earlier,
securing the inner door to the outer door.
13. Reinstall door on dryer
Doors with electrical wiring: Pull the wire through the front
panel opening before reinstalling the door.
Insert the tabs on the hinge into the mounting slot and slide
down to engage the top tab. Secure in place with the
four T25
®
screws removed earlier.
Bottom
of door
14. Reconnect wiring
Plug in wire. Using a Phillips screwdriver, secure the rotating
assembly to the hinge with the screw removed earlier.
ALL DOORS: DOORS WITH ELECTRICAL WIRING:
Swing
down
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 13 - Reinstall door on dryer.
DOORS WITH ELECTRICAL WIRING:
14. Plug in wire. Using a Phillips screwdriver, secure the
rotang assembly to the hinge with the screw removed
earlier.
27
12. Reinstall inner door assembly
Position the door with the inside of the door facing up. Using
a Phillips screwdriver, reinstall the 10 screws removed earlier,
securing the inner door to the outer door.
13. Reinstall door on dryer
Doors with electrical wiring: Pull the wire through the front
panel opening before reinstalling the door.
Insert the tabs on the hinge into the mounting slot and slide
down to engage the top tab. Secure in place with the
four T25
®
screws removed earlier.
Bottom
of door
14. Reconnect wiring
Plug in wire. Using a Phillips screwdriver, secure the rotating
assembly to the hinge with the screw removed earlier.
ALL DOORS: DOORS WITH ELECTRICAL WIRING:
Swing
down
-XQ('7_5(/($6('
,QVRPH(XURSHDQIDFWRULHVWKHOHWWHU:RIWKHSDUWFRGHPHQWLRQHGKHUHLQZLOOEHDXWRPDWLFDOO\
UHSODFHGE\WKHQXPEHUHJ:EHFRPHV
Figure 14 - Reconnect wiring.