OWNER’S MANUAL PPIOOOAC, PPI 500AC & .
WHISTLER PPIOOOAC, PPI500AC & PP2500AC Welcome To WHISTLER. For over 30 years, WHISTLER CORPORATION has been manufacturing a wide range of products designed to make your driving experience safer, more comfortable and more enjoyable. Included in the WHISTLER line is a special selection of products we call “Enhanced Driving Tools.
OWNER’S MANUAL Getting Off To A Good Start Power equipment and appliances which operate with motors or tubes require an initial surge of power to get them up and running. This power surge is referred to as the “starting load” or “peak load.” (By comparison, devices such as standard light bulbs do not require a starting load). Once the equipment or appliance has been powered up, it settles down to a slower pace and requires far less electrical power to operate.
WHISTLER PPIOOOAC, PPI500AC & PP2500AC cdZ~ To determine whether your inverter will operate a particular piece of equipment or appliance, run a test. The inverter is designed to automatically shut down in the event of a power overload and testing equipment and appliances with start up load ratings comparable the maximum wattage rating of the inverter will not damage it. Some refrigerators, freezers, pumps and other similar equipment and appliances require very high start up loads to operate.
OWNER’S MANUAL cz~ b). High Temperature LED Indicator Light. This light will turn RED and the inverter will automatically shut down when the internal temperature exceeds design parameters for safe operation. When this occurs, turn the equipment or appliance off. In the event of excess temperature, the High Speed Cooling Fan also will automatically turn on.
WHISTLER PPI OOOAC, PPI 500AC & PP2500AC ~Z) exceeds 15 volts DC. Despite this “built in” protection, the inverter may be damaged if the input voltage exceeds 15 volts DC and damage caused by excess voltage input is not covered under the WHISTLER warranty. Under optimum conditions, the voltage reading will be in the GREEN zone. Note: • In the event of automatic shut down or continuous audible alarm, turn the inverter OFF (0) until the source of the related problem has been determined and resolved. e).
OWNER’S MANUAL terminal for making a direct connection between the inverter and an electrical distribution panel. WHISTLER PP2500AC Inverter Front View a). b). c). d). e). f). g). ON/OFF Switch. High Temperature LED Indicator Light. Over Load LED Indicator Light. Battery Current & Voltage Bar Graph Meters. Twin Standard North American 110 AC Outlets. Remote Operation Socket. Circuit Breakers. (2500 Model Only). Each 110 AC outlet is equipped with a 15 amp circuit breaker. h). “Direct Wire” Connection.
WHISTLER PPIOOOAC, PPI500AC & PP2500AC i). High Speed Cooling Fan. Power Input Terminals. (BLACK/Negative, RED/Positive). (IMPORTANT: The Negative terminal on the 1000 and 1500 models is WHITE. See previous page). k). Ground Terminal Lug. j). Selecting The Optimum Power Source. Operating the inverter for extended periods combined with a high continuous load demand may result in excessive power drain from the battery.
OWNER’S MANUAL • It may be advisable to operate the inverter from a bank of batteries of the same type in a “parallel” configuration. Two such batteries will generate twice the amp/hours of a single battery; three batteries will generate three times the amp/hours and so on. This multiple parallel battery option is especially recommended for the WHISTLER 2500 due to the high level of amps this model requires to produce 2500 watts of continuous load. Wire Cable Gauges.
WHISTLER PPIOOOAC, PPI500AC & PP2500AC cdI~ (To make these connections on the 2500 model, remove the supplied nut at each terminal on the inverter, install the wire connectors flush with the metal backing plates and refasten the nuts securely. Do not overtighten these nuts). 3. Connect the wire from the Negative (—) terminal (WHITE on the 1000, 1500 models, BLACK on the 2500 model) on the inverter to the Negative (—) terminal on the 12 volt power source. Make certain the connection is secure. 4.
OWNER’S MANUAL 7. Turn the inverter ON (I). Check the Bar Graph Meter on the front panel. The Voltage Bar Graph should read between 11 and 14 volts depending on the voltage of the power source. If the reading is not within this range, check the voltage of the powersource and the terminal connections on the power source and the inverter to make sure they are secure. Neither the High Temperature or Over Load LED Indicators should be lighted. 8. Turn the inverter OFF (0).
WHISTLER PPIOOOAC, PPI500AC & PP2500AC You’ll Get A Charge Out Of This. (Or Maybe Not). Using the inverter to recharge charging units associated with such equipment as portable power tools, flashlights, video cameras and laptop computers may cause damage to the inverter or the charging unit. Although we advise against it, if you attempt to recharge a charging unit, monitor the temperature of the charging unit for approximately 10 minutes.
OWNER’S MANUAL For You Microwave Chefs. The power rating commonly associated with microwave ovens is the “cooking power” which is the power being “delivered” to the item being microwaved. The actual operating power requirement rating is higher than the cooking power rating and typically is referenced on the back of the microwave. If the operating power requirement does not appear on the back of the microwave, check the owner’s manual or contact the manufacturer. For You Technical Types. I.
WHISTLER PPI OQOAC, PP1 500AC & PP2500AC Consequently, these meters will not read the RMS modified sine wave voltage correctly and, when measuring the inverter output, the meters will read about 20 to 30 volts too low. To accurately measure of the output voltage of the inverter, use a true RMS reading voltmeter such as a Fluke 87, Fluke 8060A, Beckman 4410, Triplett 4200 or any multimeter identified as ‘True RMS.” Some Powerful Advice. The inverter will work best when placed on a reasonably flat surface.
OWNER’S MANUAL In Review. • Never attempt to operate the inverter from any power source other than a 12 volt battery. • Always ensure the power cable terminal connections run Negative (—) to Negative (-.) and Positive (+) to Positive (+). Check these connections frequently to ensure they are secure. • Use the heaviest gauge wire available to connect the inverter to the power source.
WHISTLER PPIOOOAC, PPI500AC & PP2500AC Troubleshooting PROBLEM: Low or No Output Voltage Problem Solution Poor contact with battery terminals. Clean terminals thoroughly. Battery voltage below 10.5 volts. Recharge or replace battery. Equipment being operated draws too much power. Use a higher capacity inverter or do not use this equipment. lnverter is too hot (thermal shutdown mode.) Allow inverter to cool. Check for adequate ventilation.
OWNER’S MANUAL PROBLEM: LOW Battery Alarm On All The Time Problem Solution Input voltage below 10.5 volts. Keep input voltage above 10.5 volts to maintain regulation. Poor or weak battery condition. Replace battery. Inadequate power being delivered to the inverter or excessive voltage drop. Use lower gauge wire. See “Wire Cable Gauges” Section of this manual. Keep wire length as short as possible. PROBLEM: TV Interference Problem Solution Electrical interference from inverter.
ConsumerWarranty Your Whistler product is warranted to the original purchaser for a period of three years from the date of original purchase against all defects in materials and workmanship. This limited warranty is void if the unit is abused, modified, installed improperly, if the housing has been removed, or if the serial number is missin~,• There are no express warranties covering this product otherthan those set forth in t is warranty.
If you have questions Concerning the operation of this Whistler product please call customer technical service: 1-800-531-0004 Hours: Monday Friday 9:00 am 5:00 pm EST - - WHISTLER PP1000AC WATT INVERTER SPECIFICATIONS Maximum Continuous Power 1000 Watts Maximum Surge Capability (Peak Power) 2000 Watts No Load Current Draw <0.32 A Waveform Modified Sine Wave Operating Input Voltage Range 10 - 15 Volts DC AC Receptacle Dual 3 Prong Grounded Approximate Dimensions 3.25” H x 10.25” W x 13.
WHISTLER CORPORATION 16 ELIZABETH DRIVE, CHELMSFORD, MA 01824 CUSTOMER TECHNICAL SERVICE TEL.
