Specification

ManualsBrandsWilsonart ManualsKitchen Appliance24 in. x 48 in. RE-COVER Laminate Sheet in Betty

Guide Specification

Revision: 10/19/2015 Section 06 0630 - 1

Decorative Plastic Laminate Resurfacing

SECTION 06 0630

DECORATIVE PLASTIC LAMINATE RESURFACING

PART 1 - GENERAL

1.01 SECTION INCLUDES

A. Vertical Surface Decorative Laminates.

B. High Definition Laminates.

C. Virtual Design Library Laminates.

D. Wilsonart x You Laminates.

E. Decorative Edges and Edgebands.

F. Accessory Materials.

1.02 RELATED REQUIREMENTS

A. Section 01 3000 - Submittals.

B. Section 06 0620 - Decorative Plastic Laminate.

C. Section 06 4116 - Plastic-Laminate-Clad Architectural Cabinets.

EDITING NOTE: Revise listing to suit Project requirements.

EDITING NOTE: Section listings below are common references and based on the broadly

accepted CSI MasterFormat

for Section numbers and titles. Revise to suit requirements for

particular project.

This Section specifies “Wilsonart

RE-COVER

Laminate produced by Wilsonart. RE-COVER is the

preferred product for flatwork resurfacing on fine quality residential and contract furniture, fixtures, and

casework. Architectural applications include wainscoting, valances, cornices, interior doors, and divider

systems. RE-COVER is available in the full range of Wilsonart solid colors and patterns. Wilsonart is the

largest and most-recognized manufacturer of laminates in the United States with a substantial presence

in the global marketplace.

Wilsonart RE-COVER Laminate is a self-adhesive High Pressure Laminate designed for resurfacing over

an existing High Pressure Decorative Laminate or Low Pressure Laminate (melamine) surface. Other

suitable substrates include particleboard, medium density fiberboard, plywood, and sanded paint and

stain surfaces. RE-COVER may be installed on flat surfaces in both vertical and horizontal applications.

Wilsonart

Laminates contribute to LEED-NC and LEED-CI points in several categories and have

attained UL GREENGUARD Gold Certification and SCS Gold Certification for low indoor air chemical

emissions into indoor air during product usage.

Section Editing: Informational notes will appear as “Editing Note” text boxes throughout this Section.

Bracketed bold text will require a selection to be made or information to be inserted.

Summary of content (10 pages)

PAGE 1
Guide Specification SECTION 06 0630 DECORATIVE PLASTIC LAMINATE RESURFACING ® TM This Section specifies “Wilsonart RE-COVER Laminate produced by Wilsonart. RE-COVER is the preferred product for flatwork resurfacing on fine quality residential and contract furniture, fixtures, and casework. Architectural applications include wainscoting, valances, cornices, interior doors, and divider systems. RE-COVER is available in the full range of Wilsonart solid colors and patterns.
PAGE 2
Guide Specification 1.03 D. Section 06 4219 - Plastic-Laminate-Clad Wood Paneling. E. Section 08 1423.16 - Plastic-Laminate-Faced Wood Doors. F. Section 10 2113.16 - Plastic-Laminate-Clad Toilet Compartments. G. Section 12 3530.13 - Kitchen Casework. H. Section 12 3623.13 - Plastic-Laminate-Clad Countertops. REFERENCES EDITING NOTE: Revise Reference Standards to suit Project requirements. A. Reference Standards: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 1.
PAGE 3
Guide Specification E. Quality Assurance Submittals: 1. 2. F. 1.05 Maintenance Data: Manufacturer’s published maintenance manual with closeout submittals. REGULATORY REQUIREMENTS A. Adhesives, Sealants, and Sealant Primers: 1. 2. 1.06 Test Reports: Certified test reports showing compliance with specified performance characteristics and physical properties, if required. LEED Submittals: Applicable LEED documentation for potential credits specified in this Section.
PAGE 4
Guide Specification 4. D. LEED-CI IEQ Credit 4.5 - Low-Emitting Materials, Systems Furniture and Seating. Mock-Up: EDITING NOTE: Select mock-up size option. Delete entire paragraph if mock-up is not a Project requirement. 1. 2. 3. 4. 5. 6. 1.07 1.08 Install at Project site using acceptable products and manufacturer approved installation methods. Obtain Architect’s acceptance for color, pattern, finish, fabrication, and installation standards. Mock-Up Size: [____________] by [____________].
PAGE 5
Guide Specification PART 2 - PRODUCTS WILSONART CONTACT INFORMATION: Wilsonart, 2501 Wilsonart Drive, Temple, TX 765036110. Tel. 254.207.7000, Toll-Free 800.433.3222, Fax 254.207.3209. Website: www.wilsonart.com 2.01 MANUFACTURER A. Basis of Design: Wilsonart.
PAGE 6
Guide Specification 3. Total Weight: 0.371 lbs. per sq. ft. 4. Finish Conformance Standard: AAMA 611, AA-M12C22A42/A44, Class I. EDITING NOTE: Select from one of the following color options. 5. 6. 7. 8. C. Color: [Graphite Nebula]. Color: Specified in SCHEDULE Article of this Section. Color: Indicated on Drawings. Color: Selected from manufacturer’s standard offerings. Product: “Wilsonart® RE-COVER™ Decorative Metals Type 480.” 1. 2. 3. 4. 5.
PAGE 7
Guide Specification 7. 8. 9. 2.05 Color, Pattern, and Finish: Specified in SCHEDULE Article of this Section. Color, Pattern, and Finish: Indicated on Drawings. Color, Pattern, and Finish: Selected from manufacturer’s full range of available selections. WILSONART x YOU (WxY) LAMINATES EDITING NOTE: “Wilsonart x You” creates a unique sheet of laminate from your digital artwork.
PAGE 8
Guide Specification EDITING NOTE: Wilsonart RE-COVER Laminate is NOT recommended for kitchen countertops adjacent to ranges or surface cooktops where temperatures may exceed 150 deg F (66 deg C). Suitable installations are kitchen islands, bath vanities, and utility/work rooms. E. Applications: Horizontal postformed surfaces. F. Edging: Self-edged. G. Finish: [Mirage -35] [Facet -45] [Glaze -55]. H. Color and Pattern: [_________________________].
PAGE 9
Guide Specification PART 3 - EXECUTION 3.01 EXAMINATION EDITING NOTE: Acceptable substrates for bonding Wilsonart Laminates are particleboard, medium density fiberboard, plywood with one A face, previously bonded high pressure decorative laminate, or low pressure laminate (melamine board), latex painted surfaces, and wood stained or varnished surfaces. Unsuitable substrates are plaster, concrete, gypsum board, polypropylene, polyethylene, polystyrene, and powder-coated surfaces. 3.02 A.
PAGE 10
Guide Specification B. Prior to installation, and before removing peel sheet that covers laminate adhesive, dry fit laminate to substrate. After peel sheet is removed, apply uniform bonding pressure (30 to 40 psi minimum) over the entire bonded surface, using an approved roller. 1. C. 3.05 3.06 Resurfacing laminate is NOT repositionable. Any attempts to reposition the laminate will result in inadequate bonding.