® WINEGARD TM Movin’ View Digital Satellite Mobile Antenna for Single Receiver Model MV-0055 Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300 Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 • www.winegard.com Printed in U.S.A.
Introduction/How Does Digital Satellite TV Work? Introduction Congratulations! You have purchased one of Winegard’s latest developments in the mobile satellite reception product line —the Movin’ ViewTM. This system, used with your digital satellite receiver, will deliver the best reception possible using GPS (Global Positioning System) and precision gyroscopes. How Does Digital Satellite TV Work? and processing take place.
Parts Included • Tools Needed • How to Unpack About this manual — We hope this manual will provide clear instructions to install and operate MV-0055. Two symbols have been used — ! Indicates suggestions to make processes easier for you. Indicates caution should be taken! NOTE: The MV-0055 can only be used with one (1) receiver. For multiple receiver use, contact Winegard for information on available Upgrade Kits.
Installation Diagram GPS ANTENNA FIGURE 1 SWITCH LOCATION ADJUSTABLE BASE FOOT EL MOTOR HEYCO® CONNECTORS POWER SUPPLY LEVELING SCREW COUNTERWEIGHT LEVELING SCREW FRONT OF VEHICLE ! REAR ADJUSTABLE BASE FOOT s re tie i w e v t Remong moun i hold LEVELING SCREW REAR BASE FOOT MUST DIRECTLY FACE REAR OF VEHICLE AZ MOTOR ADJUSTABLE BASE FOOT REFLECTOR 4
Installation Installing unit on roof of vehicle — ! 6. On each foot, screw the flange nut to the base of the leveling screw on the mounting foot, flange up. Place rubber washer, with the rubber side up, on the nut, Figure 2. Push mounting foot under base. Push foot screw through the base and tighten lock nut to secure foot to base. Be sure the base feet are pointing away from the base. Base feet will be removed later during install.
Installation ROOF INSTALLATION, continued GPS installation — 9. Place the unit on the roof in its permanent location and mark around the base bracket, Figure 4. (Make sure the rear adjustable base foot is directly facing the back of the coach.) The GPS antenna is pre-wired and has a 3 foot cable running through one of the Heyco® connectors.
Installation • Wiring Cable entry installation — Connecting the receiver — 1. Decide the best location for the cables to enter the vehicle, and the location of the switch and receiver (see “Installing the switch and receiver” below.) Drill a 1/2” hole in the roof, push wires inside. Make proper connections (remember you must have filtered +12 VDC power source). 2. Place cable-entry plate over hole and cables. Screw in place. Seal plate and screw holes with approved sealant (not included). 3.
Operation Your new MV-0055 features: • GPS technology • Fast signal acquisition times • Easy “one-button” operation • Ability to toggle between satellites using remote control, if subscribing to multi- satellite programming • Low maintenance • Compatible with most digital satellite receivers • Winegard warranty To operate your system — NOTE: For Model MV-0055, vehicle must be parked. 1. Turn on receiver and television set. This unit will not operate unless receiver is on.
Troubleshooting IF YOU DO NOT HAVE A SIGNAL: NOTE: The power rocker switch must be ON for the next steps. Voltage must be +12 VDC, except at the LNBF, see #2, Figure 9, page 10. 1. The signal may be blocked by trees, hills or structures. Pull into an area where no trees or buildings are in the line of sight from unit to the satellites. 6. To check voltage at connections, see Figure 9 on page 10. FOLLOW THE NUMERICAL SEQUENCE ON THE DRAWING AND CHECK VOLTAGE AT: #1. Power Supply. #2. LNBF voltage.
Base Diagram FIGURE 9 #4 COAX CABLE AT CONTROL BOX GPS ANTENNA #3 CONTROL BOX TO LNBF HEYCO CONNECTORS #1 POWER SUPPLY (POWER WIRE, SEE DETAIL) EL MOTOR GPS POWER SUPPLY CONTROL BOX (DETAIL BELOW) #2 LNBF VOLTAGE AZ MOTOR A CONTROL BOX DETAIL 10 8-PIN POWER AZ MOTOR TO LNBF EL MOTOR TO RECEIVER T DO NOT USE
Notes Features and specifications MV-0055 • One button operation. • GPS satellite signal acquisition. • Depending on receiver type, you can access satellites 119°, 110°, 101° or 92°. • No user input required. • No data port required for DISH NetworkTM, DIRECTV® or ExpressVu. • Tracking greater than 30°. • Elevation range 14.5° to 74.5°; azimuth unlimited. • 30’ power cable and 30’ coaxial cable included. • Manufactured from sturdy ABS plastic, UV protected. • Off-white color compatible with all vehicles.
Specifications & Warranty Features and specifications • One button operation. • 30’ power cable and 30’ coaxial cable included. • GPS satellite signal acquisition. • Manufactured from sturdy ABS plastic, UV protected. • Depending on receiver type, you can access satellites 119°, 110°, 101° or 92°. • Off-white color compatible with all vehicles. • No user input required. • Compact size — 32” diameter, 15” height Weight of unit - 43 lbs. Shipping weight - 59 lbs.