Operating instructions

ManualsBrandsWolf Garten ManualsLawn and GardenHSA 45 V

Safe disposal of batteries Disposal

Assembly

Attach protective shield

z Attach the protective shield as shown.

Operation

Times of operation

z Please consult regional/local regulations.

z Inquire about the operating times at your local regulatory agen-

cy.

Charging

1 Caution! The charger must only be operated in dry

rooms.

Before using the shears for the first time, charge the battery for ap-

prox. 2 hours.

Recharge only with the original WOLF-Garten charger (part no.

7420 068) !

1. Remove the battery from the hedge shears .

2. Connect the charger to the power mains (1).

3. Insert the battery into the adapter of the charger (2).

3 Instructions for the handling of the charger :

z Red LED (3) is on: Battery is being charged

z Green LED (3) is on: Charge process completed

z Red LED (3) flashing: Error

1 Self-discharge of batteries! Remove the battery from the

charger once it is fully charged.

3 General instructions regarding the battery:

In order to maintain the long service life of the battery, always

follow the instructions below:

z The hedge shears are automatically switched off when

the battery voltage is low. The battery must then be re-

charged before the shears can be used again.

z Always recharge the lithium-ion battery prior to any pro-

longed period of non-use, i.e. before storing the shears

away in autumn.

z The charging time is 2 hours for a battery that is comple-

tely empty.

z The lithium-ion rechargeable battery can be charged at

any charge level and charging can be interrupted at any

time without damaging the battery (no memory effect).

Adjust blade head

In order to ensure the same, ergonomically ideal handling in all cut-

ting situations the blade head has a 5-position latching mechanism

1 Attention! Reverse blade

Perform adjustments to the device only when the motor is off

and the blade is idle.

1. Press the locking button down (1).

2. Rotate the blade head into the desired position (2).

3. Now release the locking button.

4. Check whether the blade head is in place (the hedge shears can

only be switched on if the blade head is snapped in).

Switching the hedge shears on/off

z Make sure that your hands are steady when working above head

height.

z Hold the blade away from your body.

Motor on

1. Hold down the safety switch on the bowed handle (1).

2. Press the on/off button on the hand grip (2) at the same time.

Motor off

z Release one of the two buttons.

Tips for cutting

z Please observe the brooding season of the birds!

z The ideal hedge cutting form is the trapezoid , which provides

for adequate light and ventilation for all parts of the hedge.

z In order to promote thick growth of young hedges, only half of

new shoots should be cut.

z If the hedge has already reached the desired height, new shoots

can be completely removed.

z In order to achieve a steady hedge height you can string up a

guide wire at the desired height and cut along this wire.

z Cutting seasons:

– Deciduous hedges: May/June and October (cutback to ap-

prox. 1/3 of the total height in winter)

– Conifer hedges: April and October

– Conifers: April and October

WOLF-Garten batteries are designed

according to the latest state of technology

and optimized for the use in electric tools.

Lithium ion cells contain hazardous

substances and may therefore not be

disposed off with normal household waste.

z WOLF-Garten batteries are lithium ion cells

and are therefore subject to special

disposal regulations. Bring defective

batteries to your specialist dealer. Before

disposing of the tool, remove the battery.

z WOLF-Garten wishes to encourage users

to act in an environmentally friendly

manner. It therefore guarantees to take

back and recycle old batteries that are

returned to WOLF-Garten dealers.

z Electric tools must not be disposed with

household waste. Bring the device,

accessories and packaging to a recycling

centre for proper recycling and disposal.