ur Vote for yo ar’ at ye e th f o r e ll ‘Insta .co.uk ster-bosch www.
EXCELLENCE COMES AS STANDARD Thank you for purchasing a Danesmoor oil-fired central heating boiler. Danesmoor oil boilers are made by Worcester and the strictest quality control standards ever demanded are applied throughout every stage of production. Indeed, Worcester, part of the Bosch Group have led the field in innovative boiler design and performance for more than 40 years.
GENERAL INFORMATION To ensure you get the very best from your new Worcester Danesmoor oil boiler, please read these notes and instructions carefully. ELECTRICAL CONNECTION The electrical supply to this appliance must satisfy the latest edition IEE wiring regulations and any local regulations which apply. The mains supply to the boiler should be fed via a circuit breaker incuding earth leakage protection. The mains supply for your Danesmoor boiler is 230 volts AC-50Hz.
SERIAL NUMBER Your boiler serial number and model number should always be quoted in any contact with Worcester. This will help identify spare parts and also avoid confusion and delays during any service call-out. You will find the serial number on the front of the control facia as shown in fig.1, and access can be gained by removing the cabinet. Remove the cabinet by pulling the bottom forwards to release the ballstuds, lift the cabinet upwards and slide forwards to remove from the appliance.
(d) Turn the thermostat control knob to the desired position (see Fig. 2: temperature control). (e) Your boiler will now commence a start sequence, in which a pre-ignition period of approximately 15 seconds is followed by a supply of atomised oil being introduced into the combustion chamber. Ignition then occurs, followed by a post-ignition period of approximately 7 seconds.
MANUAL RESET OVERHEAT THERMOSTAT Sealed system installations require the use of an overheat thermostat which has to be reset by hand. Your boiler is fitted with this thermostat as standard and may be reset by pressing the button situated underneath the boiler shown in Fig.1. DUCT MANUAL RESET THERMOSTAT The boiler is fitted with a duct manual reset thermostat to prevent the appliance operating if there is a fault in a seal or insulation. The thermostat may be reset by pressing the button shown in Fig.1.
OPERATING YOUR PROGRAMMER CONTROLS Full instructions on how to install and operate the optional faciamounted programmer are included with the programmer kit. Your boiler is designed to operate on a fully pumped system only. The programmer gives fully independent programmes for central heating (CH) and hot water (HW) when the switch on the rear of the unit is set to P and the boiler is installed with a fully-pumped system. Ensure that your installer sets the switch to P on the back of the programmer.
A call-out charge will be made where: The appliance has been installed for over 24 months The appliance has been installed for more than 1 year but less than 2 years and has not had a first annual service by an approved company. OR Our Field Service Engineer finds no fault with the appliance (see note). OR The cause of breakdown is misuse or with other parts of your plumbing/heating system, or with equipment not supplied by Worcester.
MAINTAINING YOUR BOILER’S EFFICIENCY & PERFORMANCE Your new Worcester Danesmoor oil-fired boiler represents a long-term investment in a reliable, high quality product. In order to realise its maximum working life, and to ensure it continues to operate at peak efficiency and performance, it is essential that your boiler receives regular, competent servicing and annual maintenance checks beyond the initial 24 month guarantee period.
CONTACT CENTRES CONTACT NUMBERS: UK Contact Centre UK Contact Centre Scotland only Eire Tel. Fax. Fax. Tel: 08457 256 206 01905 757536 01506 441 687 01 494 0099 OPERATING HOURS: Mon - Fri Sat Sun 7.00am to 8.00pm 8.00am to 5.00pm 9.00am to 12.00pm Please contact our UK Contact Centre number where our friendly operators will book your call with one of our team of nationwide engineers. NOTE: Please refer to our website for our bank holiday hours. www.worcester-bosch.co.
YOUR WORCESTER DANESMOOR GUARANTEE This appliance is guaranteed from the date of installation subject to the following conditions & exceptions. 1. The appliance is guaranteed for a period of 24 calendar months subject to the return of the guarantee card within 30 days of installation and the first 12 months service and inspection having been carried out to the satisfaction of BBT Thermotechnology UK Ltd.
GUARANTEE REGISTRATION You should complete and return the postpaid Guarantee Registration Card within 30 days of purchase. The card will register you as the owner of your new Worcester Danesmoor boiler and, while this will not affect your statutory rights in any way, it will assist us to maintain an effective and efficient customer service by establishing a reference and permanent record for your boiler.