Sonoma Series™ VALUE Assembly Instructions for Tables with Right Front Crank #1500118 - Rev D
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank Parts for 3-leg tables, grouped by carton A I Tabletop (size and shape differ for each model) Qty: 1 For assembly of two-piece tops, please refer to separate instructions. B C Leg 1: Right Leg Qty: 1 Leg 2: Center Leg Qty: 1 D Leg 3: Left Leg Qty: 1 There are three different Value legs. If not put together in the correct order, the table will not function properly. Legs are designated as 1, 2 or 3.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank Parts for 2-leg tables, grouped by carton A B I Tabletop (size and shape differ for each model) Qty: 1 Leg 1: Right Leg Qty: 1 C Leg 2: Left Leg Qty: 1 There are two different Value legs. If not put together in the correct order, the table will not function properly. Legs are designated as 1 or 2.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 1 Verify that you have all hardware and tools needed for table assembly Check your cartons against the list on page 2 or 3 to verify that you have all the parts needed. You will also need the following tools: #2 tip Phillips screwdriver or and " combination wrench 7/16 Identify the legs and their orientation Leg 2: Two side drives at 90˚ Examine top of each leg to determine leg number.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 3 Attach Top Brackets to Legs (repeat for each leg) Attach Top Bracket to smallest end of each leg using two Button head Machine Screws and Lock Washers for each leg. S&T J or I For 3-Leg tables, Leg 2 (center leg) uses the short Top Bracket (J). Front B, C or D 4 a Attach Feet (repeat for each leg) Remove and discard silver transit screws securing plates to bottom of legs.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 5 For 3-Leg Tables: Attach Crossbar Brackets Turn legs upside down. a b Remove nuts and lock washers from leg studs. a Slide Crossbar Brackets onto studs and reinstall nuts and lock washers. Note how the flange orients to the leg. B D Right Leg Center Leg b P 6 b Left Leg C b Q P For 3-Leg Tables: Secure Center Leg to Table For base-only products, proceed to step 7.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 7 For 3-Leg Tables: Attach Crank Tubes and Crossbars to Leg 2 a Use Front Entry Hex Shaft to connect Crank Tube to gear mechanism in side of leg pointing to Leg 3 (left leg). b Use Side Entry Hex Shaft to connect Crank Tube to gear mechanism in other side of leg 2. See diagram for correct placement and orientation.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 9 a Attach Left Leg to Crank Tube, Crossbar and Table Use second Side Entry Hex Shaft to connect Left Leg to Crank Tube, inserting short end of shaft into leg and long end into Crank Tube. b Slide Crossbar over Crossbar Bracket on Left Leg and secure using two Lock Washers and Button head Machine Screws. c For base-only version, proceed to step 10.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 11 For Base-Only version: Secure Table Base to Tabletop Position the leg assembly on the face-down table top. Center the assembly on the table so that neither of the side legs overlap the edge. Mark the first two pilot holes to ensure that your table will be positioned correctly as detailed below before drilling the remaining holes.
Sonoma Series™ VALUE Workcenters - Assembly Instructions for Tables with Right Front Crank 13 Final Step Flip table over and adjust Leveling Glides if required so that table is steady and does not rock. Pull out and turn handle to raise or lower table. Replacement Part Numbers Center Leg Crossbar (Z-Bend) Bracket.............55139151 Center Leg Foot - Graphite..............................64002641 Silver.................................64002631 Center Leg Top Bracket..................................
