Quick Start Guide DashCam Wi-Fi IN-CAR CAMERA EN-1
1. Key Features y y y y y y y y 125o Wide Angle Lens. Automatic Event Video Recording for sudden external impact. Continuous loop recording for unexpected incidents. Geo-information capture in photo or video files with the built-in GPS sensor. High quality video recording up to 1296p high quality videos. Photo capture during recording. Voice Prompt. Wi-Fi Function.
2.
3.
1 2 3 4 5 6 Micro USB Port DC in Port MicroSD Slot Wide Angle Lens Reset Button Speaker Vent 7 Mounting Socket 8 9 10 Wi-Fi LED Indicator Status LED Indicator GPS LED Indicator Capture a photo during recording 11 Manually trigger an Event Protection Video Recording 12 13 Connect to PC for file browsing and file transfer Connect to the provided DC in to USB cable for charging MicroSD card storage location Capture a wide angle view Reset DashCam Wi-Fi Output the sound Install the windshield mount.
4. Installing the Windshield Mount & DashCam Wi-Fi in a Vehicle 1. 2. 3. 4. Clean the area on the windshield. Peel off the protective membrane of the 3M adhesive and stick the Windshield Mount to the front windshield inside the car. Slip the socket on the top of the DashCam Wi-Fi into Windshield Mount until it is latched. The lens of DashCam Wi-Fi should be at the center of the front windshield and be aware not to block the driver’s visibility.
5. Adjust the nut on the Windshield Mount for suitable direction and orientation.
6. Connect the DashCam Wi-Fi to the DC Power jack with included DC in to USB cable and the Dual USB CLA. Secure the cable with the cable holder to avoid interference of driver's motion.
EN-9
7. Press the Windshield Mount side to release and slide the DashCam Wi-Fi off the mount. 5. LED Indication “RED” Status LED ON “RED” Status LED Flashes continuously DashCam Wi-Fi is under Normal Looping Recording. Counting down to shut down due to power source being removed.
“ORANGE” GPS LED ON DashCam Wi-Fi is under Event Protection Recording. DashCam Wi-Fi is connecting to PC through USB cable. 1. No memory card is installed 2. Memory card is less than 8GB 3. Card error GPS signal is received. “ORANGE” GPS LED Flashes No GPS signal or GPS signal is weak. “PURPLE” Status LED ON “BLUE“ Status LED ON Blue & Red status LED alternating flash “GREEN” Wi-Fi LED ON Wi-Fi is initializing. “GREEN” Wi-Fi LED Flashes slowly Wi-Fi is ready for connection or enabled.
Fi power is turned OFF before inserting the card. A min 8GB, Class 6 or above card is recommended. Notes: 1. 2. The correct direction should be followed to insert the MicroSD card into the slot. A new MicroSD card should be formatted before using. You can format the MicroSD card through the DashCam Wi-Fi software.
6.2 Turning on/off DashCam Wi-Fi The DashCam Wi-Fi will detect car ignition vibration and automatically turn on and start Normal Looping Recording. . 6.3 Video Recording and Photo Taking Normal Looping Recording The DashCam Wi-Fi will start Normal Looping Recording once turned on. The Red status LED lights up during Normal Looping recording. Video recording is repeatedly creating successive files of 3 min, 5 min or 10 min.
Photo Taking Press once during recording to take a photo. The Status LED will flash each time a photo is taken. You can store up to 500 photos to the DashCam Wi-Fi. Please note: During recording, please do not release MicroSD card from the card slot as this may damage video or photo files. 7. Connecting the DashCam Wi-Fi via Wi-Fi 7.1 Enabling the Wi-Fi Function 1. 2. 3. 4. Connect the DashCam Wi-Fi to an external power supply with the included DC in to USB cable. The WiFi mode will turn on automatically.
7.2 Connecting the DashCam Wi-Fi to your Computer or Smart Device using Wi-Fi 1. 2. 3. Turn on the Wi-Fi mode on DashCam Wi-Fi. Go to network settings on your computer or Smart Device to enable the Wi-Fi setting. Search for the “DashCam Wi-Fi” network. Enter password “123456789” to connect to the DashCam Wi-Fi. 7.3 Using the Free App 1. 2. 3. 4. Search for iON DashCam app via the Google Play Store or App Store. Download and install the app to your smart device.
8. Connecting the DashCam Wi-Fi to a Computer You may also connect the DashCam Wi-Fi to your computer and view videos and pictures on the computer monitor. 1. Connect the DashCam Wi-Fi to your computer with a USB cable to enter into USB mode. 2. Your computer will recognize the DashCam Wi-Fi as a “Removable Disk”. The Blue Status LED will light up. Open the disk and go to relevant file folder to view, import, copy, transfer or delete the videos or photos.
Note: If the Removable Device Window did not launch automatically, go to your “My Computer” and find the device under Removable Disk. 9.
Lens Still Image Resolution on Recording Video Resolution 125 o Wide Angle Lens 3MP on 1296p 2MP on 1080p 1MP on 720p 1296P: 2304x1296 P30 1080P: 1920x1080 P30 720P: 1280x720 P30 Video Format MPEG4 (H.264) .
Language Voice Language Battery Operation Temperature English English, Mandarin 185mAh -20 to 60 degree Storage Temperature -40 to 80 degree Dimension (L x H x W) 63X51X25 mm Weight 67g+/-2g 10. Computer System Minimum Requirements Operating System Windows 7&8 / Vista / XP and Mac OS 10.5 or above CPU Pentium Ⅲ or above4 / 3.
11. Troubleshooting Problem Cause Solution Cannot turn on the DashCam Wi-Fi Low battery power Connect the DashCam Wi-Fi to a power source by DC or USB cable Cannot find removable disk after connecting the DashCam Wi-Fi to the computer Connection failure 1. Make sure all cable connections are secured 2. Restart the computer if necessary Blurry images 1. The DashCam Wi-Fi has not been installed steadily 2. The lens of DashCam Wi-Fi is dirty 1. Reinstall the DashCam Wi-Fi 2.
FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
FCC ID: NW71041 TRADEMARK INFORMATION © 2015 World Wide Licenses Limited. ® The Cool iCam logo is a registered trademark of World Wide Licenses Limited. Questions? Need Some Help? This manual should help you understand your new product. If you still have questions, visit our website: www.ioncamera.com Like Us: www.facebook.com/ioncamera Tweet Us: www.twitter.
