XOIL INSERT | LINER MODELS XOIL3019S, XOIL3619S, XOIL4219S I worked really hard on this manual so please read it...
VENTILATION When buying any XO appliance you can be confident you have chosen a high quality, innovative and stylish product from a company that cares about you! If you require service or have questions, there are 2 ways to contact our ventilation experts; Online @ https://xoappliance.com/priority-service-for-your-xo-product/ Or by phone 973-403-8900 CONGRATULATIONS on purchasing your XO. Before you proceed, take just a moment to register your XO at: www.xoappliance.
where things are GETTING READY 4 - 12 Safety and Precautions Planning Ductwork Install Examples Dimensions THE INSTALL 13 - 17 Mounting Height Top or Rear Exhaust Cut Out Dimensions Installing Electrical Connections MAINTENANCE 18 - 19 Filters Cleaning Recirculation Light Replacement OPERATING 20 - 21 The Push Button Controls Synchronizing the Remote CCC Make Up Air Conversion PARTS & WARRANTY please read and follow all safety instructions 22 - 23 It’s for your own good... Honest.
safety first CAUTION - FOR RESIDENTIAL KITCHEN USE ONLY Do Not Use to exhaust hazardous or explosive materials or vapors. NEVER voids between walls. Ducted installation must exhaust outside. Recirculating installations must exhaust back into the living space. WARNING: ELECTRICAL SAFETY This appliance must be connected to a properly grounded, dedicated 120v 60hz 15amp circuit by a qualified electrician in accordance with all applicable codes and regulations. Never use any external speed control device.
safety first continued 5
safety first continued 6
safety first continued 7
a few simple rules to plan your ductwork THIS HOOD IS DESIGNED TO USE A 6” ROUND DUCT IT MAY BE TRANSITIONED TO A 3-1/4” X 10” RECTANGULAR DUCT NEVER REDUCE DUCT SIZE. UNDERSIZED DUCTING SEVERELY RESTRICTS AIR FLOW AND HARMS PERFORMANCE. (Example: the area of a 6” Duct is more than TWICE that of a 4” Duct) KEEP DUCT RUNS AS SHORT AND STRAIGHT AS POSSIBLE. AVOID USING FLEXIBLE METAL DUCTING IF RUN IS LONGER THAN 6’. NEVER USE PLASTIC DUCTING. USE SMOOTH BORE METAL DUCTING.
estimating total equivalent feet in a duct CAUSING AIR TO CHANGE DIRECTION CAUSES TURBULENCE AND RESTRICTS FLOW IN A SYSTEM. IF USING FLEXIBLE METAL DUCT - INCREASE ALL MULTIPLIERS BY 50% (12 BECOMES 18 - ETC.) THIS EASY TO USE WORKSHEET IS FOR 600 CFM OR LESS. UNDER “QTY USED” ENTER HOW OF EACH SECTION YOU WILL BE USING. IN THE FIRST TWO ROWS - ENTER HOW MANY FEET OF EACH TYPE OF STRAIGHT DUCT YOU WILL BE USING (I.E. FOR 20 FT ENTER 20, FOR 30’ ENTER 30).
VENTED typical installation examples ROOF EXHAUST SOFFIT EXHAUST CABINET TOP EXHAUST RECIRCULATION WALL EXHAUST RECIRCULATION EXHAUST MUST BE RETURNED TO THE SPACE 10
dimensions Front of hood Side of hood 12'' 3'' 12'' “A” “B” 19-1/4'' MODEL DIM “A” DIM “B” XOIL30S 22-3/8'' 28-3/8'' XOIL36S 28-3/8'' 34-3/8'' XOIL42S 34-3/8'' 40-3/8'' Top of hood 4-9/16'' Ø6" 11
the cut out 16" 19-7/ W MODEL WIDTH XOIL3019S 28-1/2” XOIL3619S 34-1/2” XOIL4219S 40-1/2” ID TH To install the hood into a custom canopy or cabinet, refer to the cutout dimensions above for your particular model.
highs and lows RECOMMENDED MOUNTING HEIGHT ABOVE GAS COOKTOPS 27” to 32” All range hoods have a recommended range of installation height over the cooking surface. It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard; while hoods mounted too high will be hard to reach and will lose its performance and efficiency.
switching top and rear venting TO CONVERT THE UNIT FROM TOP EXHAUST TO REAR EXHAUST FOLLOW THESE SIMPLE STEPS: 1. Unplug the quick disconnect coupling that supplies power to the motor. 2. Remove the eighteen (18) screws that fasten the blower assembly and filler plate to the hood. 180° o 3. Remove the blower assembly and filler plate, invert 180 as shown and fasten in place using the eighteen (18) screws previously removed. 4. Reconnect the quick disconnect plug.
installation continued INSERT THE HOOD INTO THE CUTOUT FASTEN THE HOOD IN PLACE 1/4” 1- 1/8” Using four (4) screws along the inside front edge and four (4) screws in the back corners as shown 8x 15
installation B H B 4x BEFORE FITTING THE HOOD INTO THE CABINET: 1. Remove the four (4) screws holding the side bracket (B) in place. Remove the brackets and set aside. 2x 2 Remove the two (2) screws holding the bracket (H) in place and tilt down.
electrical connection 1. Route the power cord to the junction box inside the hood. 2. Using listed conduit fittings and connectors, connect the power supply to the box and each line to the appropriate wire following this color convention: BLACK = HOT LEG WHITE = NEUTRAL GREEN/YELLOW = GROUND Polarity must be observed. Unit must be properly grounded. Use a double throw disconnect switch. 3. Replace the box cover 4. Replace the Anti-grease Baffles.
maintenance Regular cleaning and maintenance is the key to long life and peak performance of any equipment. ANTI-GREASE BAFFLE FILTERS: Your XO hood is equipped with stainless steel pro-style baffle filters designed to capture grease from cooking. The baffles are easily removed for cleaning either by soaking in a warm, mild dish detergent solution, rinsing thoroughly and drying - or - by washing in your dishwasher. TO REMOVE THE BAFFLES: 1. Pull down on the release latch (shown left) 2.
maintenance continued FOR UNITS USED IN RECIRCULATION MODE ONLY: This refers to hoods which are not ducted outside but rely instead on carbon filter elements to help purify the air before it is exhausted back into the room. The carbon element filters gradually lose efficiency and cannot be cleaned or regenerated. These must be replaced at least 4 times a year, more frequently if needed based on the amount of use and style of cooking. CHANGING THE CARBON FILTERS: Changing the filters is easy.
easy to operate Your XO range hood is controlled by these electronic push buttons which illuminate when activated. BUTTON : Controls the LED lights. There are three illumination levels. Press the button Once for HIGH; Twice for MEDIUM; Three times for LOW; Four times for OFF. BUTTON 0: Turns both the Blower and Lights On and Off BUTTON 1: Blower motor operates on LOW speed. BUTTON 2: Blower motor operates on MEDIUM speed. BUTTON 3: Blower motor operates on HIGH speed.
make up air conversion ! w e N Code Compliance Control Some local codes limit the maximum e a Make Up Air System is required. The XOIL3019S - XOIL3619S - XOIL4219S models are supplied with 600 CFM capacity. The CCC system allows you to limit the hood from 600CFM to 395 CFM. To set up for 395 CFM Operation - follow the procedure below: 1. After the hood has been powered up initially, disconnect the power supply by shutting 2.
access parts & accessories RECIRCULATION KITS FILTERS REPLACEMENT LIGHTS REMOTE CONTROLS DUCT COVERS REPLACEMENT SWITCHES BLOWER MOTORS FAN WHEELS ALL OF THESE PARTS AND MORE ARE AVAILABLE, SIMPLY VISIT WWW.XOAPPLIANCE.
we’ve got your back 90 DAY LOVE IT or LEAVE IT. For 90 Days all our products are backed by our unique Love it or Leave it Guarantee. TWO-YEAR PARTS & LABOR LIMITED WARRANTY. XO warrants to the original purchaser of every new XO ventilation unit, the cabinet and all parts thereof, to be free from defects in material or workmanship under normal and proper use and maintenance as specified by XO and upon proper installation and start-up in accordance with the instruction packet supplied with each XO unit.
XO APPLIANCE | 24 EISENHOWER PARKWAY | ROSELAND, NJ 07068 www.xoappliance.com p. 973.403.
