XOT1830S XOT1836S NEED HELP? Call our ventilation experts toll free al 800-966-8300 AVEZ-VOUS BESOIN D’AIDE ? Contactez nos experts au numéro gratuit 800-966-8300 ¿NECESITA AYUDA? Póngase en contacto con nuestros expertos a través del número gratis 800-966-8300 USA RANGE HOOD - User instructions F HOTTE DE CUISINE - Notice d’utilisation E CAMPANA EXTRACTORA - Manual de utilización
XO Hood Warranty Proof of original purchase date and invoice is needed to obtain service under warranty. What is covered Limited 2 Year Warranty. For 2 years from the original date of purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the hood that fails because of a manufacturing defect. The warranty is extended to the original purchaser for products purchased for ordinary home use in North America.
ENGLISH USA IMPORTANT SAFETY INSTRUCTIONS FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these Instructions for the Local Electrical Inspectors use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Take care when using cleaning agents or detergents. Suitable for use in household cooking area.
C. D. E. F. G. H. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ). Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. Use proper pan size. Always use cookware appropriate for the size of the surface element. Keep fan, filters and grease laden surface clean. Use high range setting on range only when necessary.Heat oil slowly on low to medium setting. Don’ t leave range unattended when cooking.
D. Ducted fans must always be vented to the outdoors. E. This unit must be grounded. WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. A. B. C. D. E. F. WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE DANGEROUS. Do not check filters with hood working. Do not touch the lamps after a prolonged use of the appliance. No food must be cooked flambè underneath the hood. The use of an unprotected flame is dangerous for the filters and could cause fires.
Installation Preparation DUCT FITTINGS: This Hood Must Use an 6" Round Duct. It Can Transition to 3-1/4" x 10" or 3-1/4" x 12" Duct. Use this chart to compute maximum permissible lengths for duct runs to outdoors. NOTE: Do not exceed maximum permissible equivalent lengths! Maximum duct length: 100 feet for range hoods. Flexible ducting: If flexible metal ducting is used, all the equivalent feet values in the table should be doubled.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape. INSTALL THE DUCTWORK: NOTE: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2.
› Front of hood 1-3/8" › Side of hood 1-13/16" 3-1/4" 3" 18" 10" 12" › Top of hood › Mounting height and clearance: 22" Hood Specifications PRODUCT DIMENSIONS AND CLEARANCE XOT1830S - XOT1836S: 30" - 36" Min 27" - Max 32" 36" -8-
INSTALLATION INSTRUCTIONS INSTALLATION - VENTED TO THE OUTSIDE 1. ATTENTION! - Before carrying out assembly operations, open the packaging, take the hood and place it on a comfortable surface. - Remove the anti-grease filter/s (Fig.1A). A - If hood installation is used with the air outlet Fig.1B or Fig.1C, the wires set-up in the relevant fairleads must be released by pulling the lever outwards, as indicated in figure 2 - phase 1-2.
lowing the steps in reverse (Fig.2). In this way it will be easier to manoeuvre the unit. - If the appliance id to be mounted in DUCTING version, prepare the air evacuation hole. - It is recommended to use an air evacuation pipe with the same diameter as the air outlet flange. The use of a reduction could decrease product performance and increase noise. I M P O R TA N T - T h e r a n g e h o o d m u s t b e s e c u r e d t o w a l l studs or use drywall anchors capable of supporting 75 lbs.
Attention! This product envisions the air evacuation hole available in 2 different positions, which can be used according to your requirements; 1 – in the upper part of the hood Fig.3A. 2 – in the rear part of the hood Fig.3B. - The air evacuation flange is supplied with the rectangular shape X and circular shape Y (Fig.3). A B X Y D D Fig.
t 7FSTJPO XJUI BJS FWBDVBUJPO IPMF JO UIF upper part of the hood (Fig.4A): This product is supplied with the air outlet in the upper part and the electric connection box positioned in the rear part of the hood, as indicated in figure 4B (see paragraph: connection to the electric power supply). - If a rectangular air outlet pipe is used E, the hood is already set-up (Fig.4A.1). - If, however, a circular air outlet pipe is to be used F, the 7 screws H must be removed along with the bracket X (Fig.4A.2).
t 7FSTJPO XJUI BJS FWBDVBUJPO IPMF JO UIF rear part of the hood (Fig.5A): - If your requirements envision the use of the air outlet in the rear part of the hood (carry out all phases shown in figure 5B), remove the screws I (Fig.5A.1) that fix the motor bracket Y and turn the entire motor unit and position it as indicated in Fig.5A.2. Put the motor bracket Y back in its seat and fix it with the previously removed screws I.
POWER SUPPLY: IMPORTANT – (Please read carefully) WARNING: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances.
2. CONNECT ELECTRICAL: t 1PXFS 4VQQMZ $POOFDUJPO For connection to the power supply refer to the following Fig.6: 1. Break and remove the small circular metal sheet positioned in the rear part of the hood, with the aid of a flat screw driver Fig.6.1. 2. Remove the power supply lid by loosening the 2 screws A Fig.6.2. 3. Connect the wires of the hood to those of the power supply as described Fig.6.
OPTIONAL: the electric power supply box can be removed and fixed in the position indicated in Fig.7A. WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING Before connecting the appliance to the power supply network, the electric plant box must be positioned in the seat. To move the electric power supply box, refer to that indicated in Fig.7A: 1. Loosen the two screws C Fig.7A.1. 2.
t The appliance must be installed at a minimum height of 27" from an electric cooker stove, or 32" from gas or combined cooker stoves. If a connection ductwork composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the range hood exhaust duct air to the same duct air used to exhaust hot air or fumes from other appliances other than electrical. 3.
t 5IJT QSPEVDU DBO CF JOTUBMMFE JO 2 different ways: - Mounting the hood in the lower part of the shelf: 1 type installation Fig.8. - Mounting the hood on the wall: 2 type installation Fig.8. 1 A B 4 2 A 1 B Fig.
t .PVOUJOH UIF IPPE JO UIF MPXFS QBSU PG UIF TIFMG 'JH " - Check that the screws used that are not supplied with the product are suitable for the type of object. - Position the fixing template on the lower part of the shelf (Fig.9B), (considering the minimum distance from the cooker top). - Make 6 holes in the shelf respecting the measurements indicated(Fig.9C). - Fix the 4 screws A without tightening them completely.
C 30" 36" 6" 3- 1/ 4" 10" 12" 10" 1-3/4" 10" 3" 3" 18" 18" 19-3/8" 1-13/16" X 3-1/4" 1-13/16" 1-13/16" Y 12" 3-1/4" 22" 22" 6-1/16" H I 2" 2" 2" 3-1/2" 2" 15-15/16" 2-1/4" 9/16" 7" 29-15/16" 9/16" 4" 30" 6-1/16" 3" H I 3-1/2" 15-15/16" 2-1/4" 9/16" 3" Fig.
t .PVOUJOH UIF IPPE PO UIF XBMM 'JH " Position the fixing template on the wall (Fig.10B), (considering the minimum distance from the cooker top). - Make 4 holes respecting the measurement indicated in the figures (Fig.10C). - Fix the 2 upper screws A without tightening them completely along with the plugs. - Hang the hood on the wall, aligning it in a horizontal position and tighten/fasten the 2 screws A. When it has been regulated, fix it definitively using the 2 safety screws B.
C 30" 36" 6" 3- 1/ 4" 10" 12" 1-13/16" X 10" 1-3/4" 10" 3" 3" 18" 18" 19-3/8" Y 12" 3-1/4" 3-1/4" 1-13/16" 1-13/16" 22" 22" 6-1/16" H I 2" 2" 2" 3-1/2" 2" 15-15/16" 2-1/4" 9/16" 7" 29-15/16" 9/16" 4" 30" 6-1/16" 3" H I 3-1/2" 15-15/16" 2-1/4" 9/16" 3" Fig.
DUCTLESS RECIRCULATING OPTION: 30" 36" b " " 30 36 a c CARBON FILTER KIT XORFK07 (30") - XORFK08 (36"): The kit includes an air diverter A, 7 screws B and 2 round filters C. 1 X Fig.1: Take the rectangular shape X and fasten it to the hood using the 7 screws. To convert this model from the sunction to the filtering version, it is not necessary to use the rectangular shape X.
1 2 Fig.2: Remove the aluminum panels by pulling the lever 1 out and pushing downwards 2. a b b Fig.3: Take the bracket A and fasten it to the hood using the 7 screws B (provided). Take the 2 round filters C and apply them onto the bracket as shown in the figure.
c Fig.4: The filters C must be applied to the suction unit inside the hood, centering them inside of it and turning them 90° until they snap into place. 1 2 Fig.5: Put the aluminum panels back in place (Fig.2).
USE t *G UIF BQQBSBUVT JT FRVJQQFE XJUI UIF following controls: A = LIGHT B = OFF C = SPEED I D = SPEED II E = SPEED III G = MOTOR WORKING indicator.
MAINTENANCE t We recommend that the cooker hood is switched on before any food is cooked. We also recommend that the appliance is left running for 15 minutes after the food is cooked, in order to thoroughly eliminate all contaminated air. The effective performance of the cooker hood depends on constant maintenance; the anti-grease filter and the active carbon filter both require special attention.
- DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust. - DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals with may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces should be cleaned with warm water and mild detergent only.
t 3FQMBDJOH IBMPHFO MJHIU CVMCT In order to replace the dichroic lamps, carefully remove the lamp from the lamp holder with the help of a small flat screwdriver or a similar tool. PLEASE NOTE! In doing this operation, please take care not to scratch the hood. Replace the bulbs with new ones of the same type.
XOT1830S - XOT1836S: 659 423 171 100 29 110 554 165 12 609 492 39 120 261 70 - 30 - 40 140
OPTIONS AND ACCESSORIES: Model XORFK07 (30") - XORFK08 (36") Ductless Recirculating Filter Kit.
OPTIONS AND ACCESSORIES: Model XORFK07 (30") - XORFK08 (36") Ductless Recirculating Filter Kit.
XOT Spec Sheet Model: XOT1830S - XOT1836S Sizes: 30" - 36" Depth: 22" Features and Benefits: - 600 CFM high velocity blower optimally removes Smoke, Grease and Odors. - 3 speed push button controls. - Two 50W Halogen Lights - Provide brilliant illumination over the cooking surface. 1/ 1-13/16 " 3- 4 10" 2" - Dimensions: 30" or 36" x 22" D x 18" Tall. 1 1-3/8" - Baffle Filters - Trap airborne smoke and grease particles. They can be easily be removed for dishwasher-safe cleaning.