Operating Manual

ManualsBrandsYaesu Musen ManualsElectronicsHH AMATEUR SCANNING RECEIVER

Controls & Connections

FT-70DR/FT-70DE Operating Manual

Icon Description of operation

Lights when a function key is pressed (Secondary Keypad Active)

AMS（Automatic Mode Select） Feature Active

TX Power Level Indicator (LOW/MID TX Power Selected)

TX POWER ICON TX Power Meter during

HIGH (5 W) ： (disappear）

MID （2 Ｗ）：

LOW （0.5 Ｗ）：

Dual Watch Active

APO (Automatic Power-Off) Active

Bell Ringer Active

Locking the key and knobs

GM Feature Communication range indicator

:Stations within your communication range

:Stations outside of your communication range (blnk)

V/D mode (simultaneous voice and data communication mode)

Voice FR mode (Voice full-rate mode)

Analog FM mode

AM mode (Receive only)

DTMF Autodialer Active

ApplicationforFCC/IC

FCCID:K6620515X20,IC:511B-20515X20

Summary of content (10 pages)

PAGE 1
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Controls & Connections Icon Description of operation Lights when a function key is pressed (Secondary Keypad Active) AMS（Automatic Mode Select）Feature Active TX Power Level Indicator (LOW/MID TX Power Selected) TX POWER ICON HIGH (5 W)： (disappear） TX Power Meter during MID （2 Ｗ）： LOW（0.
PAGE 2
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Preparation Installing the Antenna 1. Align the bottom side of the antenna with the antenna connector on the transceiver. Caution Be sure to hold the thick base of the antenna when installing it. 2. Turn the antenna clockwise until it is secured. zz Do not hold or twist the upper part of the antenna when installing or removing it. To do so may break the conductors inside the antenna. zz Do not key the transmit without installing the antenna.
PAGE 3
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Preparation Installing the Battery Pack 1. Insert the battery pack into the battery compartment on the back of theradio while tilting the Belt Clip outward. 2. Push the battery pack in until the battery latch clicks securely. 3. Slide the battery pack lock plate to the“UNLOCK”position beside the battery latch until the entire “LOCK” appears. Unlock Lock Removing the Battery Pack 1.
PAGE 4
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Chraging the Battery Pack If the battery has never been used, or its charge is depleted, it may be charged by connecting the SAD-11 or SAD-18B Battery Charger, as shown in the illustration, to the EXT DC jack. It takes about 6 hours to charge the SBR-24LI battery pack fully. The optional Rapid Charger Cradle (SBH-28) requires about 2.5 hours to charge the SBR24LI battery pack. Charging the Battery Pack using the Battery Charger 1.
PAGE 5
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Chraging the Battery Pack Charging the Battery Pack using the Rapid Charger 1. Insert the plug of the battery charger (SAD-11 or SAD-18B) into the DC IN jack of the rapid charger (SBH-28). 2. Install the battery pack to the transceiver. You can charge the battery pack alone (not attached to the transceiver), by inserting it into the rapid charger.  3. Turn the transceiver off. 4. Place the transceiver in the rapid charger. Charging starts.
PAGE 6
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Chraging the Battery Pack Connecting an External Power Supply for Use in Vehicle The optional external power supply adapter with a cigarette lighter plug (SDD-13) allows the transceiver to be used in a vehicle. 1. Turn off the transceiver. 2. Insert the plug of the external powersupply adapter with a cigarette lighter plug (SDD-13) in the EXT DC IN jack of the transceiver. 3.
PAGE 7
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Chraging the Battery Pack Connecting to an External Power Supply Using a Power Cable The optional power cable (E-DC-6) allows the transceiver to be connected to an external power supply. 1. Turn off the transceiver. 2. Connect the optional external power supply cable (E-DC-6) to an external power supply.
PAGE 8
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Basic Operation Turning on the Transceiver 1. Press and hold [POWER] switch. When the transceiver is turned on for the first time after purchase, the call sign input message appears on the LCD. The next time, the frequency screen will appear after the opening screen. When the transceiver is turned on the second time, and subsequently, the frequency screen appears. zz Be sure to set the call sign ID using the FT-70DR/DE.
PAGE 9
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Basic Operation Adjusting the Volume Level 1. ‌R otate the DIAL knob while pressing and holding the key to set the desired audio level. Clockwise rotation increases the volume level. zz ‌If no sound is heard from the speaker, press and then adjust the volume level while listening to white noise. zz Press [F] key, then press the [MONI] (T-CALL) Key to adjust the squelch level. Selecting a Frequency Band 1.
PAGE 10
Application for FCC / IC FCC ID: K6620515X20, IC: 511B-20515X20 Basic Operation zz In factory settings, Auto Step mode is set so that the transceiver is automatically switched to the optimal frequency steps for the receiver frequency. zz In factory settings, turning the [DIAL] knob beyond the selected frequency band causes the transceiver to switch to the next frequency band. To change the tuning so the frequency will move repeatedly through the selected band, enter the Set mode, then select [74 VFO.