FCC ID: K66VX-2R VX-2R OPERATING MANUAL General Description Accessories & Option Accessories Supplied with the VX-2R FNB-82LI 3.7 V, 1000 mAh Rechargeable Lithium Ion Battery Packs NC-85B/C/U 2.5-Hour Charger Belt Clip Hand Strap Antenna Operating Manual Warranty Card Available Option for your VX-2R FNB-82LI 3.7 V, 1000 mAh Rechargeable Lithium Ion Battery Packs NC-85 B/C/U 2.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL level. DIAL The main tuning Dial is used for setting the operating frequency, and also is used for menu selections and other adjustment. TX/BUSY This indicator glows green when the squelch opens, and turns red during transmit. During Emergency Operation, this indicator will glow (or flash) white. PTT (Push To Talk) Press this switch to transmit, and release it (to receive) after your transmission is completed.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL Keypad Functions Key BAND H/L V/M FW HM/RV % MD Press Key Moves operation to the next-highest frequency band. Switches the transmit power output between “HI” and “LOW.” Switches frequency control between the VFO and Memory System. Activates the “Alternate” key function. Press + [FW] Key Moves operation to the next-lowest frequency band. Select the synthesizer steps to be used during VFO operation.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL If using an external antenna for transmission, ensure that the SWR presented to the transceiver is 1.5:1 or lower. Installation of FNB-82LI Battery Pack The FNB-80LI is a high-performance Lithium-Ion battery providing high capacity in a very compact package. Under normal use, the FNB-82LI may be used for approximately 300 charge cycles, after which operating time may be expected to decrease.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL Operation R. F. says: Hi! I’m R. F. Radio, and I’ll be helping you along as you learn the many features of the VX-2R. I know you’re anxious to get on the air, but I encourage you to read the “Operation” section of this manual as thoroughly as possible, so you’ll get the most out of this fantastic new transceiver. Now. . .let’s get operating! Switching Power On and Off 1. Be sure the Battery Pack is installed, and that the battery is fully charged.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL 5. When you are satisfied with the Squelch threshold setting, press the PTT key momentarily to save the new setting and exit to normal operation. R.F. Says: 1) A special “RF Squelch” feature is provided on the VX-2R. This feature allows you to set the squelch so that only signals exceeding a certain S-meter level will open the squelch. See page ?? for details.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL frequency. If you press the [F/W] key momentarily, then rotate the DIAL, frequency steps of 1 MHz will be selected. This feature is extremely useful for making rapid frequency excursions over the wide tuning range of the VX-2R. 2) Scanning From the VFO mode, press and hold the [BAND] key. The VX-2R will begin scanning toward a higher frequency, and will stop when it receives a signal strong enough to break through the Squelch threshold.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL leaving 430 MHz on High power, and the radio will remember the different settings on both band. And when you store memories, you can store High and Low power settings separately in each memory, so you don’t waste battery power when using very close-in repeaters! 2) When you are operating on one of the Low power settings, you can press the [F/W] key, when press the PTT switch, to cause the VX-2R to transmit (temporarily) on High power.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL The red illumination yields clear viewing of the display in a dark environment, with minimal degradation of your night vision. Three options for activating the lamp are provided: KEY Mode: Illuminates the Keypad/LCD for five seconds when any key pressed. CONT Mode: Illuminates the Keypad/LCD continuously. OFF Mode: Disables the Keypad/LCD lamp. Here is the procedure for setting up the Lamp mode: 1. Press and hold the [H/L] key for one second to enter the Set mode.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL 5/9/10/12.5/15/20/25/50/100 kHz per step, any number of which may be important to your operating requirements. The VX-2R is set up at the factory with different default steps on each operating band which probably are satisfactory for most operation. However, if you need to change the channel step increments, the procedure to do so is very easy. 1. Press and hold the [H/L] key for one second to enter the Set mode. 2.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL Repeater Operation Repeater stations, usually located on mountaintops or other high locations, provide a dramatic extension of the communication range for low-powered hand-held or mobile transceivers. The VX-2R includes a number of features which make repeater operation simple and enjoyable. Repeater Shifts Your VX-2R has been configured, at the factory, for the repeater shifts customary in your country.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL 3. Press the [H/L] key momentarily to enable adjustment this Item. 4. Rotate the DIAL knob to select the desired shift among “–RPT,” “+RPT,” and “SIMP.” 5. When you have made your selection, press the PTT key to save the new setting and return to normal operation. Changing the Default Repeater Shifts If you travel to a different region, you may need to change the default repeater shift so as to ensure compatibility with local operating requirements.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL called “CTCSS” (Continuous Tone Coded Squelch System), is included in your VX-2R, and is very easy to activate. R.F. Says: CTCSS setup involves two actions: setting the Tone Frequency and then setting of the Tone Mode. These actions are set up by using the [MD] key or Set Mode Items 18: SQL TYP and 19: TN FRQ. 1. Press and hold the [MD] key for one second. This provides a “Short-cut” to Set Mode Item 18: SQL TYP. 2.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL similar to that just described for CTCSS. Your repeater system may be configured for DCS; if not, it is frequently quite useful in Simplex operation if your friend(s) use transceivers equipped with this advanced feature. R.F. Says: Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCS and that you select a tone code. 1. Press and hold the [MD] key for one second. This provides a “Short-cut” to Set Mode Item 18: SQL TY 2.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL DCS, “DCS” will appear on the display. 2. Press and hold the [H/L] key for one second to enter the Set mode. 3. Rotate the DIAL knob to select the Set Mode Item 19: TN FRQ when TONE SQL is selected, or Set Mode Item 20 DCS CD during DCS operation. 4. Press the [H/L] key momentarily to enable adjustment of the selected Menu Item. 5. Press and hold the [BAND] key for one second to start scanning for the incoming CTCSS or DCS tone/code. 6.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL programming. Split Tone Operation The VX-2R can be operated in a Split Tone configuration via the Set mode. 1. Press and hold the [H/L] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select the Set Mode Item 23: SPLIT. 3. Press the [H/L] key momentarily to enable adjustment of the selected Menu Item. 4. Rotate the DIAL knob to select ON (to enable the Split Tone feature). 5.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL ARTS-equipped station are within communications range. This may be particularly useful during Search-and Rescue situations, where is important to stay in contact with other members of your group. Both stations must set up their DCS codes to the same code number, then activate their ARTS feature using the command appropriate for their radio. Alert ringers may be activated, if desired.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL R.F. Says: ARTS won’t work if you have used the Lock feature to disable the PTT! ARTS Polling Time Options The ARTS feature may be programmed to poll every 25 seconds (default value) or 15 seconds. The default value provides maximum battery conservation, because the polling signal is sent out less frequently. To change the polling interval: 1. Press and hold the [H/L] key for one second to enter the Set mode. 2.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL feature is enabled. The callsign field may contain up to 16 characters. Here’s how to program the CW Identifier: 1. Press and hold the [H/L] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select the Set Mode Item 39: CW ID. 3. Press the [H/L] key momentarily to enable adjustment of the selected Menu Item. 4. Rotate the DIAL knob to select ON (to enable the CW ID function). 5.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL 1. Press and hold the [H/L] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select the Set Mode Item 24: DTMF. 3. Press the [H/L] key to enable adjustment of this Menu Item. 4. Rotate the DIAL knob to select the DTMF Memory register into which you wish to store this DTMF string. 5. Press the [H/L] key momentarily, then rotate the DIAL knob one click clockwise to select the Set Mode Item 25: DTMF S. 6.
FCC ID: K66VX-2R VX-2R OPERATING MANUAL page ?? for details on setting the Home channel. The “Emergency” feature is activated by press and holding the [HM/RV] key for one second.