Operation Manual

ManualsBrandsYale ManualsBackupSR340

Smart Home

Alarm Kits

Installation · Programming · Operating

Keep this manual safe for reference and future maintenance

Contents

Thank you for choosing the Yale Smart Home Alarm

System. This simple to install system has been designed

with the user in mind.

All the components are self contained and no wired

connections are needed between the units. There is no

need to damage the home decor, lift carpets or run cables.

You can install up to 20 devices (Max. 6 PIR Image / Video

Cameras) in this system. As well as extra Door/Window

Contacts, PIR Motion Detectors and Smoke Detectors,

you can add Key Fob remote controls for added control

convenience.

Regular testing and battery changes (when notied by the

system) will ensure reliability and peace of mind.

There is no need to wire into the mains supply or seek

the services of a qualied electrician. The Smart Hub is

All accessories are ‘tamper’ protected. Any unauthorised

tampering with these items when the system is armed will

result in the alarm being triggered.

1. Location planning 2

2. Un-pack all the parts 4

3. Initial set-up 5

3. Additional accessories 6

4. Mounting devices 8

5. Using the system 10

6. About your Alarm System 12

7. Using accessories 13

8. Changing the batteries 15

9. Troubleshooting 17

10. Specications 19

Recommended Installation Sequence

We recommend you follow the simple install

sequence, headings numbered 1-5.

Information and illustrations are subject to change within this

document. Yale reserves the right to alter the specication and

product design at anytime without notice. Yale® is a registered

smart

Living

Issue No: 1A

The 2 year guarantee for this Yale Smart

Home Alarm Kit is active from the date

of purchase (A copy of this guarantee is

available on our website).

Please register online within

12 months of purchase at

www.yale.co.uk/registeryourproduct

For more information on this product and Yale Smart

Living Range visit www.yale.co.uk/smart-living

Consumer Support: info@yale.co.uk

Summary of content (20 pages)

PAGE 1
Smart Home Alarm Kits smart Living Installation · Programming · Operating Keep this manual safe for reference and future maintenance Contents Thank you for choosing the Yale Smart Home Alarm System. This simple to install system has been designed with the user in mind. 1. Location planning 2 2. Un-pack all the parts 4 All the components are self contained and no wired connections are needed between the units. There is no need to damage the home decor, lift carpets or run cables. 3.
PAGE 2
1 Location Planning Work out the best places to locate the devices for maximum protection. Having chosen the locations do not mount at this stage. Home and Away Mode Planning The Home Arming mode allows the premises to be part armed so that no one can get inside without warning the occupier, yet the person already inside the house can move freely without triggering the alarm.
PAGE 3
Smoke Detector External Siren • Mount in the middle of the ceiling at the top of a stairwell, or on the centre of hallway ceilings where smoke would most likely be detected. • Do not mount in corners or above cooking appliances and heaters. • Install additional detectors if there are closed doors preventing smoke from reaching detectors. Choose a position on an external wall where the siren would be most prominent. Mount as high as possible, out of easy reach.
PAGE 4
Smart Hub 2.0 Key Pad EF-KP 1. Unpack the kit content on a table. Remove the mounting plate (if fitted) from the Smart Hub by sliding plate downwards. A power adaptor is supplied that plugs into the main wall socket and Smart Hub. Plug in the power adaptor and connect the Smart Hub to your internet router using the cable provided. 1. Pull out the plastic battery saver tab at the back of the Key Pad. This will activate the batteries. 1 2 7 8 4 Away / Battery Switch Cover 2.
PAGE 5
3 Additional Accessories External Siren EF-BX (SR-320, 330 & 340 kits) Keyfob EF-KF (Sold Separately) 1. Open the battery compartment using a coin by turning cover in the direction of the big arrow so the small arrow is next to round dot. 2. Insert CR2032 battery (supplied) and replace cover. Away / WARNING The Siren is very loud, be prepared! Take care not to activate the Siren tamper switch unnecessarily. • Remove the cover by unscrewing the single screw located on the lid.
PAGE 6
Initial set-up Please ensure all devices are powered and operational at this point. Download Yale App (Smartphone) Search term in App Store: Yale Home System Compatibility: iOS 9, Android 4.2+ Internet Connection: Required on Smartphone First time registration Start The Yale Home System App on your phone. *Due to continuous improvement, please note that the graphic may differ from shown. Panel MAC / Serial Number: Select New user click here Further down on this start page you can set Language.
PAGE 7
Adding Accessories (if you purchased extra accessories) All accessories in the kit are linked to the Smart Hub. If you purchased extra accessories (or for some reason the accessories are deleted), please do the following: 1 1. Press and hold the learn button on your Smart Hub. you will hear a beep, after 6 seconds you will hear a slightly longer beep. 2. Your Smart Hub is now in learn mode. 2 One by one, press the learn button on the accessory according to below.
PAGE 8
4 Mounting Devices Smart Hub 2.0 Mounting The Smart Hub can be free standing, either vertically or horizontally on a flat surface with access to mains socket and broadband internet router. It is also suitable for wall mounting. Using the two holes on the mounting back plate, mark the position of the holes. Drill two holes and fix with the screws and plugs provided. Hook the Smart Hub onto the plate. Check Accessories Range Mounting the PIR & PIR Image/ Video Camera 1.
PAGE 9
Mounting the Door/Window Contact Mounting the External Siren Ensure the tamper spring is fully compressed when the siren is mounted. If there is a gap, pack with a suitable spacing material. Note:The Door/Window Contact and magnet can be changed round as long as there is no more than a 10mm gap. 1. Find a location on the door/window where you would like the device to be mounted. The sensor should be on the frame while the magnet should be on the door/ window.
PAGE 10
5 Using the System Note! The PIR Motion Detector and PIR Image Camera have a built in battery save mode. After detecting motion, they will wait for one minute without motion before sending any signals to the Smart Hub. This saves battery power. Changing your Key Pad PIN The default Key Pad PIN is 1234.
PAGE 11
Manually requesting PIR Images During an alarm, the PIR Image/Video Camera will send images/video to your phone. You can also manually request these images/video. Still images take an average of 15 seconds before showing on your phone, and video takes approximately 1 minute. Click on “image” to view images/videos. Note: Up to 50 images/videos can be kept in the Yale Server (the oldest images/videos are automatically deleted to make space). Users are advised to delete unwanted images/videos.
PAGE 12
6 About your Alarm System (Default Settings) All accessories (except SR-PC and SR-PVC) are pre-set to “entry” mode. When the system is first armed, users will have 30 seconds to exit the building. If the system is already armed, triggering any sensors will cause an entry countdown to begin. SR-PC/SR-PVC’s default setting is “Burglar only”, i.e. immediate triggering during full arm and sleep during Home Arm. This is done to conserve battery life.
PAGE 13
7 Using Accessories To provide additional flexibility and protection you can add extra Key Fobs, Key Pads, Panic Buttons and Smoke Detectors. These are available separately from your local stockist. Adding Accessories to your System (See page 7) Key Pad Key Pad Initialisation If you purchase a Key Pad as an extra Key Pad, you will need to initialise it prior to use with the Smart Hub. 1 Press ‘Panic button A’ followed by factory default Key Pad code ‘0000’.
PAGE 14
7 Using Accessories (cont.) Reset Key Pad code If the Key Pad code is accidentally forgotten, the Key Pad can be reset to factory default (0000) using the following steps: 1. Unscrew the two Key Pad case screws and remove Key Pad back cover (please disable tamper first). Locate and remove the battery. See battery change section (16-17) 2. Press the number ‘4’ key at the same time as reinserting the battery. Testing • Smoke Detector testing should be done on a regular monthly basis.
PAGE 15
8 Changing the Batteries Always use correct type of batteries as replacements because any other battery can cause problems with the operation of the system. Ensure the correct steps are taken when changing batteries in tamper protected devices. Low Battery Indication The App will display the low battery message under the actual device. PIR Motion Detector & Image / Video Camera Battery Change When the battery is low the LED will flash when any motion is detected. The batteries are changed as follows: 1.
PAGE 16
8 Changing the Batteries (cont.) Key Fob Battery Change Panic Button Battery Change When the battery is low the LED will glow dimly when any key is pressed. The battery is changed as follows: When the battery is low the LED will glow dimly when the button is pressed. The battery is changed as follows: 1. Using a coin turn the battery cover anticlockwise to the unlocked position and remove cover and battery. 1. Loosen the bottom case screw and take button cover off base. 2.
PAGE 17
9 Troubleshooting External Siren Siren produces a 3 second alarm when disarmed • There has been a previous alarm and there might be an intruder still in the premises. Siren produces a series of audible pips when armed or disarmed • If the Siren produces a series of pips when arming and disarming this indicates low batteries. • If the Siren produces a series of pips only when arming this indicates a tamper fault.
PAGE 18
9 Troubleshooting (cont.) PIR Motion Detector LED flashes • Batteries are low or the tamper switch is disturbed. Check that the tamper switch spring is making contact with base. If the tamper switch is OK, change batteries with new AA alkaline replacements (see page 15). PIR Motion Detector does not respond to movement • Batteries are completely exhausted.
PAGE 19
10 Specifications All devices Environmental Conditions -10°C to 40°C, relative humidity 70% noncondensing for all units except the external Siren. Siren: -20°C to 50°C, relative humidity 95% noncondensing Radio operational range 30m in a typical domestic installation, range can vary depending on building construction, device positions and RF environment Housings ABS/polycarbonate Smart Hub 2.0 Siren Output 100dBA sound pressure @ 1m minimum Zones 20 radio devices Radio system 868MHz FM, 2.
PAGE 20
smart Living ASSA ABLOY Ltd.