Yale Assure Lock® 2 Keyed Deadbolt Installation Guide (Keypad YRD410 or Touchscreen YRD420) Notice: Before installing your lock, be sure to follow the steps on the yellow Quick Start Guide.
In The Box Hardware Components DoorSense Screws Adjustable Deadbolt Latch (AYRDB DRIVE Strike Adjustable Drive-In Deadbolt Plate Latch available for purchase) Flush Mount Cap Yale Smart Module (with select models) Mounting Tape Housing Guide Cover Key Exterior Keypad Reset Pin Battery Cover x4 AA x2 Strike Plate and Deadbolt Screws x20mm AA Screws and Plastic Clips (pre-installed) x2 x2 x2 x2 Optional Security Strike Plate Screws AA AA Screw Set D Screw Set C Screw Set B Silver for Bl
1 Remove Existing Deadbolt Keep your old deadbolt until your new lock has been successfully installed.
2 Check Door Measurements and Adjust If Needed 1/8 Check Door: Tear off the Door Checker page of this guide and follow instructions to verify your door measurements and make any needed adjustments.
Verify Measurements with the Check Your Door Guide Measure Clearance X Measure Door Thickness Measure Backset Greater than A B, C, or D Equals E or F Less than A (Your door is not a match for a Yale smart lock) X Less than B X Less than E or F X Greater than D X Greater than E or F Backset 2-3/8" (60mm) or 2-3/4" (70mm) (Your door is not a match for a Yale smart lock) (Your door is not a match for a Yale smart lock) (Your door is not a match for a Yale smart lock) Cut Here (Your door is not
1/8 3/8 5/8 1/4 0 7/8 1/8 3/8 5/8 1/4 3/4 1/2 1 7/8 1/8 3/4 5/8 1/4 1/2 I 3/8 7/8 1/8 1/2 5/8 1/4 3/4 2 3/8 3 7/8 1/8 3/4 1/2 3/8 5/8 1/4 4 7/8 1/8 5/8 1/4 3/4 1/2 3/8 5 7/8 1/8 5/8 1/4 3/4 1/2 3/8 6 7/8 3/4 1/2 7 A G B C Blue Black H E F CAUTION: If printed from electronic file, set print scale to 1:1. Measure ruler to check scale. D Silver Check Your Door Guide A.
Template to Mark a Door for 2-1/8" Face Bore For 1-3/4" (44.5mm) Thick Door Center of 1" (25mm) hole through edge of door For 1-3/8" (35mm) Thick Door Trusted every day FOLD OVER DOOR EDG E Cut Here Center of 1" (25mm) hole through edge of door 2-3/4" (70mm) Backset Center of 2-1/8" (54mm) hole through face of door CAUTION: If printed from electronic file, set print scale to 1:1. Measure a dimension to check scale.
Template to Mark a Door for 1-1/2" Face Bore For 1-3/4" (44.5mm) Thick Door For 1-3/8" (35mm) Thick Door Trusted every day Center of 1-1/2" (38mm) hole through face of door CAUTION: If printed from electronic file, set print scale to 1:1. Measure a dimension to check scale.
3 Install Deadbolt Latch and Strike Plate 2-3/8"Backset, Out of Box *Correct deadbolt latch length is based on backset. Choose 2-3/8" or 2-3/4". Door Checker measurements E and F can help you verify your backset measurement. 2-3/8 Security screws can be used here, in place of the small strike plate screws. x2 For Deadbolt Latch (Actual Size) To Adjust: Twist neck while holding body stable.
4 Verifying Bore Face Measurement for Exterior Keypad Install the lock with the door open. Do not close until all steps are completed. Measurement G on the Door Checker will help verify your bore face measurement. If hole is less than 2-1/8", remove adapter by unscrewing the two screws on either side, using a Phillips #2 screwdriver. Inside of Door Outside of Door Ensure deadbolt latch is unlocked to allow tailpiece to slide through deadbolt latch. See Step 3, if not.
5 Install Mounting Plate and Exterior Keypad Inside and Outside of Door IMPORTANT: There are 3 bolt sets with your lock. Choose the bolt length for your door thickness. Measurement B, C, or D on the Door Checker will help you identify which bolts to use.
6 Attach Wire to Inside of Interior Lock Ridges face outward Make sure wire is attached securely.
7 Install Interior Lock Tailpiece must be vertical. Insert tailpiece into the slot. Push the lock towards the door, adjusting the position until the plate spring latch ‘clicks’ into place and holds the bottom of the lock. Tailpiece Thumbturn Slot Thumbturn Lock Hook Trusted every day Screws are pre-installed. Tighten when lock is seated on plate. When fully tightened, lock should be flush to door.
Test Thumbturn and Key Smooth deadbolt latch operation will enhance your battery life. If deadbolt latch does not lock or unlock when turning thumbturn: Ensure tailpiece is inserted into deadbolt latch slot. Step 4 Ensure tailpiece is inserted into thumbturn slot. Step 7 Trusted every day If deadbolt latch does not lock and unlock when key is turned: Ensure deadbolt latch is centered in face bore hole. Step 3 Ensure tailpiece is inserted into deadbolt latch slot.
S Select Models Install Yale Smart Module Included with select models Batteries must not be installed when inserting or removing Yale Smart Module.
8 Install Batteries and Replace Cover Place ribbon behind batteries for easy battery removal. 2nd 1st Deadbolt latch must be unlocked before installing batteries. The numbers will begin to light up in a clockwise motion. Once this happens, the lock is in pairing mode and can be set up using the Yale Access App. Pink Light and Audio Sounds Successful Power up Try to connect your lock quickly as this mode will turn off after 5 minutes.
9 Installing DoorSense® Surface Mount Installation Installation options: Step 1. Determine mounting location 1. Surface Mount: Only requires only the use of a screwdriver. 2. Flush Mount: Provides a cleaner and less visible look with more robust performance, but does require drilling a ⅝" hole into your door frame. For optimal performance, DoorSense should be mounted within 1.5" from the edge of your door frame, and align with your lock’s Smart Module (if you are installing one).
9 Installing DoorSense® Step 2. Attach mounting tape C. Remove the remaining piece of adhesive. A. Remove one side of the adhesive. B. Attach tape to the back of the DoorSense, ensuring it is aligned with the edges of the device and screw holes. Trusted every day Step 3. Place on door frame Press the adhesive side to the frame.
9 Installing DoorSense® Step 4. Screw into frame Hand tighten to the frame using the included screws. You may wish to complete this step after your lock is set up and calibrated to ensure you are able to retrieve accurate door state readings before modifying your door frame. Step 5. Attach the cover Notes: Once the lock has been set up, navigate to the Lock Settings and select Calibrate Lock. Follow the instructions in the app. Open and close the door to validate the door state is accurate.
9 Installing DoorSense® B. Press the cap onto the notched side of the magnet carrier. The two shapes should interlock. Flush Mount Installation What you’ll need • Flush Mount Cap (shown in illustration on page 16.) • 5/8" drill blade bit • Electric drill Step 1. Remove magnet from the housing Use a small blunt object to push the magnet carrier out of the housing. This may require some force. Step 2. Assemble magnet to cap A. Expose the adhesive by removing the blue backing.
9 Installing DoorSense® Step 4. Tape drill bit It may be helpful to attach tape to your drill bit to mark the proper depth of hole to drill. Although DoorSense requires a 1/2" deep hole, it may be helpful to use the assembled DoorSense Flush Mount as a guide. Door Frame 5/8 Tape set at 1/2" Depth Mark Step 5. Drill hole Drill the hole in the proper location on your door frame. Trusted every day Step 6.
Using Your Lock Exterior Keypad Interior Lock Battery Cover Wake or One Touch Locking To Unlock the Door 1. Press the Yale logo on the exterior keypad. 2. Enter the entry code. 3. Press the .
Features Feature Description DoorSense • DoorSense tells you if your door is closed or open. Note: You can only ask a Voice Assistant if the door is locked or unlocked. Entry Codes • • • • Entry Codes are used to unlock your door. Create entry codes from the “Guest List” screen in our app. You can set the entry code to work permanently, recurring, or on a temporary schedule. An unlimited number of entry codes can be created or deleted at any time.
Setting Definitions Setting Default Definition Codes Automatically Programming Code created by the Yale Access App This code is used to access programming features: Handing, Smart Module integration, and Diagnostics. This code cannot be used to unlock the door. Find your programming code in the Yale Access App, enter this code on the keypad and press the gear symbol. Entry Codes Entry codes can be created,from the Yale Access App, for users to allow them to lock/unlock the door from the lock keypad.
Setting Definitions Setting Default Definition Advanced Device Settings Volume On This feature can be changed in the Yale Access App. You can turn the lock volume on or off. Operating Mode: Normal On When the lock is in normal operating mode all entry codes will work and the lock can be unlocked/locked from the app and voice assistants. Operating Mode: Vacation Off This feature can be enabled in the Yale Access App. When enabled all entry code access will be restricted.
Troubleshooting Symptom Suggested Action Lock does not respond door is open and accessible. • • • • Lock does not respond door is locked and inaccessible. • Batteries may not have enough power. Replace batteries*. • Use mechanical key to unlock the door. Lock is on for a while then shows no reaction. Lights dim. • Batteries do not have enough power. Replace batteries*. Lock chimes indicating code acceptance, but door will not open. • Check for any foreign objects between door and frame.
Troubleshooting Symptom Suggested Actio n Entry code will not register. • • • • Upon entering an entry code and pressing the check key, the lock displays “invalid code” error or lock times out without responding. • Verify entered code is a valid, previously programmed, 4 to 8 digit code. • Vacation mode is on. Only an admin user can change vacation mode. Contact the admin. Upon entering an entry code and pressing the check key, lock responds “Wrong number of digits”.
Hardware Troubleshooting Symptom Solution Deadbolt grinds and will not extend to lock when using an entry code but thumbturn locks and unlocks smoothly. Attempt re-handing using the Settings Menu. You must use Programming Code to access the Settings Menu. Deadbolt is hitting the strike plate. Reposition the strike plate to align with deadbolt. Deadbolt is not fully extending. Increase depth of the deadbolt strike pocket in frame. Adjust your existing knob, lever or handleset strike plate.
Resetting Lock to Factory Defaults When lock is reset*, it will remove the lock from the Yale Access App and remove all pin codes and settings that were changed. Reset Pin Remove 1 battery to reset lock. Do not install Smart Module with batteries installed. To Reset Lock: 1. Remove battery cover and one battery. 2. Press reset button for 1 minute with the reset tool provided in the hardware box. 3. Replace cover.
Keypad Alerts Trusted every day Keypad Meaning Gear flashes Amber Low Battery Level 1 Gear flashes Red Low Battery Level 2 Gear flashes Red then stays red until batteries are replaced Low Battery Level 3 Checkmark flashes Pairing Success X then gear flashes Red Jammed Lock Gear flashes White Pairing/successful pairing Gear flashes Red during pairing Failed Pair 30 P/N YRD400-KD-0022 Rev A Part of ASSA ABLOY
Interior Lock Light Alerts Inside Lock Light Meaning Blue flashing Low Battery Level 1 Blue flashing Low Battery Level 2 Blue flashing Low Battery Level 3 Pink flashing Passage Mode enabled Red flash Locked state Green flash Unlocked state Green 3 second solid Pairing Success Red 3 second solid Pairing Fail Light Trusted every day 31 P/N YRD400-KD-0022 Rev A Part of ASSA ABLOY
Use: Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Apple®, Apple Home™, Apple Watch®, HomeKit®, and iPhone® are trademarks of Apple Inc., registered in the U.S. and other countries and regions.
