B RECEIVER/DVD PLAYER OWNER'S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit (RX-E810 and DVD-E810) in a well ventilated, cool, dry, clean place with at least 10 cm on the top (2.5 cm for DVD-E810), 10 cm on the left and right, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
Contents Features .................................................................. 2 Supplied Accessories ............................................. 2 Controls and Functions ......................................... 3 Receiver (RX-E810) .................................................. 3 DVD player (DVD-E810).......................................... 6 Remote control........................................................... 8 TUNER OPERATIONS FM/AM Tuning ............................................
01EN_01_Intr_MCR-E810_B.fm Page 2 Wednesday, August 23, 2006 4:25 PM FEATURES Features Receiver (RX-E810) • Maximum RMS output power per channel 65W + 65W (6 Ω, 1 kHz, 1%THD) • 40-station FM/AM preset tuning • iPod dock terminal • Pure Direct mode DVD player (DVD-E810) • Plays DVDs, Video CDs, Audio CDs, MP3 CDs, WMA CDs, DivX CDs and JPEG CDs.
Controls and Functions INTRODUCTION Receiver (RX-E810) ■ Front panel 1 2 3 45 6 7 8 9 NATURAL SOUND STEREO RECEIVER RX-E810 PURE DIRECT DISPLAY TIMER MEMORY AUTO/MAN'L TIME ADJ TIMER PRESET/BAND PRESET/TUNING VOLUME BASS STANDBY/ON TREBLE HOUR MIN INPUT BALANCE PHONES L R MIN 0 A B C D E MAX F 1 STANDBY/ON Turns the receiver on or sets it to the standby mode (see page 19).
Controls and Functions ■ Rear panel 1 2 3 ANTENNA 75 UNBAL. SPEAKERS (Europe model) MAINS 6 MIN / SPEAKER DOCK FM DVD/CD AC OUTLETS SWITCHED R L GND IN OUT TAPE/MD AM SUBWOOFER OUT TO DVD-E810 100W MAX. TOTAL AUX R 4 5 L 6 1 DOCK terminal Use to connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) where your iPod can be stationed (see page 17). 2 Antenna terminals See page 15 for connection information. 3 Speaker terminals See page 13 for connection information.
Controls and Functions ■ Front panel display 2 3 4 SLEEP PRESET STEREO AUTO TIMER TUNED MEMORY 5 6 7 8 INTRODUCTION 1 DOCK SHUFFLE REPEAT PS PTY RT CT PTY HOLD PLAYLISTS ARTISTS ALBUMS SONGS GENRES D 9 0 A B 1 SLEEP indicator Lights up when the sleep timer is on (see page 44). 2 PRESET indicator Lights up when you preset radio stations manually (see page 39). 3 STEREO indicator Lights up when the receiver is receiving a strong signal from an FM stereo broadcast.
Controls and Functions DVD player (DVD-E810) ■ Front panel 2 1 NATURAL SOUND DVD PLAYER 3 4 DVD-E810 STANDBY/ON PROGRESSIVE 5 6 7 8 9 0 1 Disc tray Holds a disc to be played back. 6 PROGRESSIVE indicator Lights up when the progressive scan mode is on (see page 54). 2 Opens and closes the disc tray. 7 Front panel display Shows the current status of the DVD player. 3 s Stops playback (see page 25). 8 Remote control sensor Receives signals from the remote control.
01EN_01_Intr_MCR-E810_B.fm Page 7 Friday, September 1, 2006 4:55 PM Controls and Functions ■ Rear panel 1 (U.K. and Europe models only) INTRODUCTION AV MAINS VIDEO OUT COMPONENT PR DIGITAL OUT AUDIO OUT L Y COAXIAL OPTICAL TO RX-E810 S VIDEO 2 VIDEO 3 R PB 4 5 6 7 8 1 AV terminal (U.K. and Europe models only) See page 14 for connection information. 5 COAXIAL jack See page 16 for connection information. 2 S VIDEO jack See page 14 for connection information.
Controls and Functions Remote control DVD/CD • Playback • Subtitle and audio language selection, etc. TUNER • Radio station tuning • Radio station preset, etc. DVD/CD mode TUNER mode STANDBY/ON This remote control has two main operation modes to control this system. Before operating functions in each mode, you need to select a mode to change the remote control key assignments. To switch the operation mode • DVD/CD mode: Press DVD/CD. • TUNER mode: Press TUNER.
Controls and Functions ■ DVD/CD mode 7 SET UP Displays the setup menu on the TV screen (see page 51). 8 SUBTITLE Selects the subtitle language (see page 30). POWER TV 1 2 5 6 9 1 2 3 4 5 6 3 4 7 8 SCAN DIMMER 0 A-B REPEAT TV CH FREQ/TEXT PROG MODE PTY SEEK TV INPUT ON SCREEN START SHUFFLE PRESET MENU 0 9 ANGLE Selects a viewing angle (see page 31). A B 0 Number keys (1 to 9, 0) Input numerals to specify parameters or chapter/track numbers. C D E INFO.
Controls and Functions ■ TUNER mode Operations available in TUNER mode The following operations are available for the receiver. y STANDBY/ON Press TUNER to set the remote contol to the TUNER mode before carrying out the following operations. POWER TV 1 2 3 4 5 6 7 8 SCAN DIMMER 9 0 FREQ/TEXT PROG MODE PTY SEEK TV INPUT ON SCREEN 1 Number keys (1 to 8) Selects preset station number (see page 39). 2 Radio Data System tuning keys (U.K.
Controls and Functions ■ Installing the batteries in the remote control ■ Using the remote control NATURAL SOUND STEREO RECEIVER RX-E810 PURE DIRECT Press DISPLAY TIMER MEMORY AUTO/MAN'L TIME ADJ TIMER PRESET/BAND PRESET/TUNING VOLUME BASS STANDBY/ON TREBLE HOUR MIN INPUT BALANCE PHONES Within 6 m (20 feet) L MIN 30˚ 1 Press the mark on the battery cover and open the cover. 2 Insert the two supplied batteries (AA, R06, UM-3) into the battery compartment.
CONNECTING THE SYSTEM Connecting the System Make sure you read the following procedure and notes carefully before connecting the system. For information on the speakers (NX-E800), refer to the owner’s manual supplied with it. Note Do not connect the power cable of the receiver, DVD player, or other components to the wall outlet until all cable connections are completed. Right speaker (NX-E800) Left speaker (NX-E800) 3 3 MAINS ANTENNA 75 UNBAL.
Connecting the System ■ Connecting the speaker cable 4 Tighten the knob to secure the wire. Notes 1 Red: positive (+) Black: negative (–) PREPARATION • Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.
CONNECTING A TV Connecting a TV Follow the procedure below to connect your TV to the DVD player using the supplied video pin cable. Also, you can enjoy high-quality pictures with a S-video connection, a component video connection or a scart connection (U.K. and Europe models only) using a corresponding commercially available cable. For information on your TV, refer to the owner’s manual supplied with it.
CONNECTING ANTENNAS Connecting Antennas To enjoy radio on the receiver, connect the supplied AM and FM antennas to the designated terminals. If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use optional outdoor antennas. For details, consult the nearest authorized YAMAHA dealer or service center.
CONNECTING EXTERNAL COMPONENTS Connecting External Components You can connect various audio components, such as an MD player, a tape deck or a YAMAHA iPod universal dock to the receiver. Also you can connect an MD recorder or a CD recorder to the DVD player using the DIGITAL OUT jacks. For information on your external component, refer to the owner’s manual supplied with each component.
Connecting External Components Connecting a YAMAHA iPod universal dock The receiver (RX-E810) is equipped with the DOCK terminal on the rear panel that allows you to connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) where you can station your iPod and control playback of your iPod using the supplied remote control. Connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) to the DOCK terminal on the rear of the receiver using its dedicated cables.
01EN_02_Pre_MCR-E810_B.fm Page 18 Wednesday, August 23, 2006 4:42 PM CONNECTING THE POWER CABLES Connecting the Power Cables Once all connections are complete, connect the power cable of the DVD player to the AC OUTLET(S) terminal on the rear of the receiver (or the AC wall outlet if the AC OUTLET(S) terminal is not available), and then plug the power cable of the receiver into the AC wall outlet. MAINS ANTENNA 75 UNBAL.
SETTING THE SYSTEM Setting the System Before starting playback operation, follow the procedure below to configure the system settings.
Setting the System 5 Press TIME ADJ once again to confirm the clock setting. “Adjusted” appears in the front panel display for a few seconds, and then the clock appears. 4 4:3 PAN SCAN Select this if the aspect ratio of your TV is 4:3 and you want both sides of the picture to be trimmed or formatted to fit your TV screen. 4:3 LETTER BOX Select this if the aspect ratio of your TV is 4:3. In this case, a wide picture with black bands on the upper and lower portions of the TV screen are displayed.
Setting the System Step 5: Set the the default audio, subtitle, and disc menu languages If you set the default audio, subtitle, and disc menu languages, the DVD player automatically switches to the selected language when a disc is loaded. If the selected language is not available on the disc, the default language of the disc will be used instead. (The default setting is “ENGLISH” for audio and disc menu and “OFF” for subtitle.
Basic Receiver Operations Basic Receiver Operations Follow the procedure below to select an input source and adjust the sound settings on the receiver. PHONES 3 Start playback on the selected source component or select a broadcast station. For information on the disc playback, see page 25, and for information on tuning, see page 37. 4 Press VOLUME +/– to adjust the volume to the desired output level.
Basic Receiver Operations Changing the front panel display settings Follow the procedure below to change the settings of the receiver’s front panel display. ■ To switch the display mode STANDBY/ON You can switch the information displayed in the receiver’s front panel display between the current input and clock. POWER TV 1 2 3 4 5 6 7 8 SCAN DIMMER 9 0 Note You cannot display the clock unless you adjust it (see page 19). DIMMER Press DISPLAY repeatedly to select the desired display mode.
Supported Disc Types Supported Disc Types You can enjoy movie or music discs with the DVD player. Since some disc operations are limited to specific disc types, the supported disc types are indicated using the icons shown below. Each means that the operations is limited to the corresponding disc type. Operations with no icon indicated are available for all disc types. Note Depending on a disc format, some discs may not be compatible with the DVD player.
Basic Disc Playback Operations Basic Disc Playback Operations Follow the procedures below to carry out basic disc playback operations. Notes To advance frame-by-frame DVD • If the inhibit icon ( ) appears on the TV when a button is pressed, it means the function is not available on the current disc or the current status. • Depending on the disc, some operations may be different or restricted. Press e to pause playback, then press e repeatedly.
Basic Disc Playback Operations ■ To repeat between two points (A-B Repeat) Repeating disc playback (Repeat Play) You can repeat the specified section of a chapter (track) by setting two points (start and end points). You can repeat the playback of the selected item in a disc. Also, you can set two points to repeat the specified section of a chapter (track) with A-B Repeat. Notes • Repeat Play may not work depending on DVD disc types.
Basic Disc Playback Operations 2 Press SHUFFLE to select the desired Shuffle Play mode. Each time you press the key, the mode changes as follows. ↓ 2 Press or to select “TT TIME” or “CH TIME”, and then press . TT TIME: Select this if you want to specify an elapsed time for the current title. CH TIME: Select this if you want to specify an elapsed time for the current chapter. 3 Use the number keys to enter hours, minutes, and seconds. Playback skips to the specified position.
Basic Disc Playback Operations Specifying a preview picture for playback (Scan Search) DVD VCD You can preview the content of a DVD or VCD with pictures selected at regular intervals, and specify a preview picture for playback. Notes • You can only select “TRACK INTERVAL” during VCD playback when the PBC menu (see page 31) is turned off. • CHAPTER DIGEST and CHAPTER INTERVAL are not available for DVD-VR discs.
Basic Disc Playback Operations Customizing playback order (Program Play) You can customize the playback order for chapters or tracks stored in the disc. This unit can memorize playback order of 10 discs (20 chapters or 20 tracks for each disc). y • To cancel the Program Play feature, use the cursor keys to select “EXIT” in the program list, and then press ENTER. • To remove a chapter or track programmed in the list, use the cursor keys to select the program number to be cleared, and then press ENTER.
Basic Disc Playback Operations Selecting audio and subtitle languages DVD /audio channel settings VCD Zooming the picture DVD VCD You can zoom in or zoom out the picture during disc playback. You can select audio and subtitle languages for DVD disc playback and audio channel settings for VCD. If no language is selected, the default languages specified in the setup menu (see page 21) are selected. ON SCREEN PRESET MENU INFO.
Basic Disc Playback Operations Selecting a viewing angle DVD You can select the desired viewing angle during DVD playback. Note This selection is available only with multi-angle compatible discs. Also, viewing angles available for each disc may vary. For information on your disc, refer to the operating instructions in the disc’s menu or on its jacket. TV VOL VOLUME Operating the disc menu Many DVDs and VCDs (SVCDs) include original navigational menus called “DVD menu” and “Playback Control (PBC) menu”.
Basic Disc Playback Operations Playing back MP3/WMA/JPEG/DivX discs You can play back MP3, WMA, and DivX format files recorded on a CD-R/RW, DVD+R/RW, and DVD-R/RW. Also you can view JPEG files in the commercially available JPEG discs (such as KODAK Picture CDs) or recorded on a CD-R/RW, DVD+R/RW, and DVD-R/RW. 2 Press or to select a folder, and then press ENTER. The file list of the selected folder appears on the TV screen. 3 Press , , or number keys to select a file, and then press ENTER.
Basic Disc Playback Operations ■ About DivX Media Format (DMF) DivX Media Format (DMF) enables you to play back the DivX files with interactive features such as interactive menus, alternate audio and subtitles. Follow the procedure below to operate the interactive menu. 1 Load a disc into the DVD player. The interactive menu appears on the TV screen. 2 Use the cursor keys to select a chapter. 3 Press ENTER or p to start playback from the selected chapter.
Basic Disc Playback Operations Viewing or changing playback settings on the TV (OSD menu) DVD VCD You can view and change the settings for the DVD or VCD (SVCD) currently played back. Note Displaying the OSD menu for a VCD or SVCD automatically closes the PBC menu (see page 31). 1 STANDBY/ON POWER TV Number keys 1 2 3 4 5 6 7 8 SCAN DIMMER 9 0 y For CDs, each time you press ON SCREEN, the time display changes as follows: TOTAL ELAPSED → TOTAL REMAIN → SINGLE ELAPSED → SINGLE REMAIN.
Restricting Disc Playback Restricting Disc Playback DVD You can set playback restrictions for certain discs using the parental control or disc lock feature. Only users who know the password (see page 36) can access the locked discs. Setting the parental control level 3 You can restrict playback according to a predetermined level (parental control level). For information on the parental control level of each disc, refer to the instruction on its jacket.
Restricting Disc Playback Locking a disc Changing the password You can prevent up to 40 specific discs from playback by locking the discs. Follow the procedure below to change the password to access locked disc temporarily. 1 While the disc to be locked is loaded into the unit, press SET UP. 1 Press SET UP. The setup menu appears on the TV screen. 2 Press or to select “GENERAL SETUP PAGE”, press or to select “DISC LOCK”, and then press .
FM/AM Tuning There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use the automatic and manual preset tuning features to store up to 40 stations (A1 to E8: 8 preset station numbers in each of the 5 preset station groups).
FM/AM Tuning ■ To switch the frequency step (Asia and Taiwan models only) Automatic preset tuning Because the interstation frequency spacing differs in different areas, you may need to switch the frequency step mode. Follow the procedure below to preset radio stations automatically.
FM/AM Tuning Manual preset tuning Selecting preset stations You can also store up to 40 stations (A1 to E8: 8 preset station numbers in each of the 5 preset station groups) manually. You can tune into any desired station simply by selecting the preset station group and number under which it was stored (see page 38).
Radio Data System Tuning (U.K. and Europe Models Only) Radio Data System Tuning (U.K. and Europe Models Only) Radio Data System (U.K. and Europe models only) is a data transmission system used by FM stations in many countries. The Radio Data System function is carried out among the network stations.
Radio Data System Tuning (U.K. and Europe Models Only) 4 Press PTY SEEK START to start searching for available Radio Data System preset stations. If a station broadcasting the selected program type is found, the receiver stops searching, and then program service name and the PTY HOLD indicator lights up in the front panel display. If there is no station broadcasting the selected program type, the frequency currently selected appears.
Radio Data System Tuning (U.K. and Europe Models Only) ■ Additional CT (clock time) settings You can use CT information received from the Radio Data System stations to adjust the built-in clock of the receiver. STANDBY/ON 3 POWER CT→Clock Set this to “ON” if you want to apply CT information received from the Radio Data System stations to the built-in clock of the receiver. (The default setting is “ON”.
Setting the Timer The receiver is equipped with 2 types of timer functions: clock timer and sleep timer. The clock timer automatically turns the receiver on or sets it to the standby mode at the specified time. The sleep timer sets the receiver to the standby mode after the specified time elapses. The DVD player also turns on or sets to the standby mode automatically if it is connected to the receiver using a system control connection (see page 12).
Setting the Timer Setting the sleep timer The sleep timer sets the receiver to the standby mode after the specified time elapses. A-E ENTER A-E TOP MENU /RETURN SET UP TV VOL VOLUME DISPLAY SLEEP SLEEP DVD/CD TUNER BAND TAPE/MD AUX/TV DOCK SUBTITLE ANGLE ZOOM AUDIO Press SLEEP repeatedly to select the desired duration. Each time you press the key, the duration changes as follows. The SLEEP indicator lights up in the front panel display. SLEEP 120 min. SLEEP 90 min. SLEEP 60 min.
Setting the auto-standby mode You can turn on/off the auto-standby feature which automatically set the system to the standby mode if you do not operate the system for 30 minutes while the receiver is set to the DVD/CD input mode. (The default setting is “AUTO STANDBY ON”.) Notes • Unless you connect the receiver and the DVD player properly with the supplied system control cable (see page 12), this feature does not function for the system. • This feature does not function for the system during playback.
CONTROLLING EXTERNAL COMPONENTS Controlling External Components In addition to controlling the receiver (RX-E810) and DVD player (DVD-E810), you can operate the specific functions for external components made by YAMAHA or an iPod connected with a YAMAHA iPod universal dock (such as YDS-10 sold separately) using the supplied remote control. To control a TV made by other manufactures, you need to set up the appropriate remote control code (see page 48).
Controlling External Components ■ DOCK mode STANDBY/ON 0 Cusor keys ( / / / ), ENTER Press to return to the upper level in the iPod menu. Press or to select an item in the selected group. Press or ENTER to enter the selected group. (Pressing ENTER starts playback when a song is selected.) POWER TV 1 2 3 5 6 7 8 SCAN DIMMER 9 1 4 0 5 TV CH STANDBY/ON A-B REPEAT POWER TV FREQ/TEXT PROG 2 MODE PTY SEEK TV INPUT START SHUFFLE 3 4 ■ TAPE mode ON SCREEN PRESET MENU INFO.
Controlling External Components Setting remote control codes You can control TVs made by other manufactures by setting the appropriate remote control code (refer to “LIST OF REMOTE CONTROL CODES” at the end of this manual). Follow the procedures below to set the remote control code. STANDBY/ON 1 Press AUX/TV to set the remote control to the AUX/TV mode.
Controlling External Components Using iPod Once you have stationed your iPod in a YAMAHA iPod universal dock (such as YDS-10 sold separately) connected to the DOCK terminal of the receiver (see page 17), you can enjoy playback of your iPod using the supplied remote control. The operations of your iPod are available with the aid of the receiver’s front panel display (menu browse mode) or without it (simple remote mode). Notes • Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
Controlling External Components ■ Menu browse mode In the menu browse mode, you can operate the iPod menu using the receiver’s front panel display. Also you can configure the “Setup” parameters with the menu browse mode. 2 Note Press or to select the menu, and then press or ENTER to enter the selected menu. The name of the first item stored in the selected menu appears. There are some characters that cannot be displayed in the front panel display of the receiver.
Configuring the DVD Player Settings (Setup Menu) In the setup menu, you can configure the various parameters or operate useful functions related to the DVD player. Follow the procedure below to operate the setup menu. For details on each menu or available parameters, see “Setup menu items” on page 52. STANDBY/ON Press DVD/CD to set the remote control to the DVD/CD mode. 2 Press SET UP. The setup menu appears on the TV screen.
Configuring the DVD Player Settings (Setup Menu) Setup menu items The following table explains details on the setup menu items of the DVD player. For instructions on operating the setup menu, see “Configuring the DVD Player Settings (Setup Menu)” on page 51. Page Menu GENERAL DISC LOCK SETUP PAGE PROGRAM Submenu See page 36 for details. (Default: UNLOCK) INPUT MENU See page 29 for details. OSD LANGUAGE See page 20 for details.
Configuring the DVD Player Settings (Setup Menu) Page Menu Submenu AUDIO CD UPSAMPLING *1 SETUP PAGE Parameter You can convert your music CD to a higher sampling rate using sophisticated digital signal processing for better sound quality. If you have activated the upsampling, the DVD player will automatically switch to the stereo mode. (Default: OFF) OFF: Disables the CD upsampling function. 88.2kHz (X2): Converts the sampling rate of the CDs twice higher than original. 176.
Configuring the DVD Player Settings (Setup Menu) Page Menu Submenu VIDEO PROGRESSIVE *4 SETUP PAGE *2 PICTURE SETTING Parameter When connecting the DVD player to a progressive scan compatible TV using a component video connection, you can enjoy high-quality DVD video with the progressive scan mode. (Default: OFF) ON: Enables the progressive scan. OFF: Disables the progressive scan. You can select the picture color setting from three predefined sets or configure in detail.
Configuring the DVD Player Settings (Setup Menu) Page Menu Submenu PREFERENCE AUDIO PAGE *5 SUBTITLE See page 21 for details. (Default: ENGLISH) See page 21 for details. (Default: OFF) DISC MENU See page 21 for details. (Default: ENGLISH) PARENTAL See page 35 for details. (Default: 8 ADULT) VR LIST You can select the original list or play list used for playback of VR (Video Recording) format discs.
Configuring the DVD Player Settings (Setup Menu) Resetting the DVD player settings You can reset all options and your personal settings to the initial factory settings, except your password for “PARENTAL” and “DISC LOCK”. ON SCREEN PRESET MENU INFO. ENTER A-E A-E TOP MENU /RETURN SET UP Cursor keys, ENTER SET UP TV VOL VOLUME DISPLAY SLEEP DVD/CD TUNER BAND TAPE/MD AUX/TV DOCK DVD/CD SUBTITLE ANGLE ZOOM AUDIO 1 Press DVD/CD to set the remote control to the DVD/CD mode.
Language Codes If your desired language for “AUDIO”, “SUBTITLE” and “DISC MENU” is not listed in the setup menu (see page 21), select “OTHERS”, then enter the 4-digit language code for your desired language.
TROUBLESHOOTING Troubleshooting Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized YAMAHA dealer or service center. Receiver (RX-E810) ■ General Problem Cause Remedy See page The receiver fails to turn on or enters the standby mode soon after the power is turned on.
Troubleshooting ■ Tuner Problem FM stereo reception is noisy. FM AM Cause The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. Remedy See page Check the antenna connections. 15 Try using a high-quality directional FM antenna. — Use the manual tuning method. 37 There is distortion, and clear reception cannot be obtained even with a good FM antenna. There is multi-path interference.
Troubleshooting ■ iPod Note In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod (see page 17). Status message Loading... Cause Remedy See page The receiver is in the middle of recognizing the connection with your iPod. The receiver is in the middle of acquiring song lists from your iPod. Connect error There is a problem with the signal path from your iPod to the receiver.
Troubleshooting DVD player (DVD-E810) Problem Cause Remedy See page Power turns on but immediately shuts off. The power cable is not connected or the plug is not completely inserted. Connect the power cable firmly. 18 Power immediately shuts off during playback. Auto-standby function of the receiver works when the receiver can not receive the playing signal transmitted from the DVD player with the system control cable for 30 minutes.
Troubleshooting Remedy See page You may use a CD-R/RW, DVD+R/RW or DVD-R/RW that is not finalized. Finalize the CD-R/RW, DVD+R/RW or DVD-R/RW. — The disc label may not be facing up. Check that the disc label is facing up. — The disc may be defective. Try to play back another disc. If the same problem does not happen, the disc you want to play back is defective. — JPEG or MP3/ WMA disc may not contain sufficient picture files or music tracks to be played back.
Notes on Discs Disc information The following tables explain the disc types supported by the DVD player. y Disc logo marks are printed on the disc and the disc jacket. Note Do not load any other type of disc into the DVD player. Doing so may damage the DVD player. The DVD player can play: – DVD+R/RW and DVD-R/RW discs recorded in DVD-Video compatible format. – DVD-RW discs recorded in VR format (compatible with CPRM). • The following discs cannot be played on the DVD player.
Notes on Discs Handling a disc • Do not touch the surface of the disc. Hold a disc by its edge and center hole. • Do not leave a disc in the tray when you are not playing it. • Do not write on the disc with a pencil or other marker. • Do not stick tape, seals or other attachments to a disc, and do not bring into contact with glue. • Do not use a protective cover to prevent scratches. • Do not use a disc whose surface can be printed with a commercially available label printer.
Glossary Audio information ■ Dolby Digital ■ Sampling frequency Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio. With 3 front channels (left, center, and right), and 2 surround stereo channels, Dolby Digital provides 5 full-range audio channels. With an additional channel especially for bass effects, called LFE (low frequency effect), the system has a total of 5.1-channels (LFE is counted as 0.1 channel).
Glossary Video information ■ Component video signal With the component video signal system, the video signal is separated into the Y signal for the luminance and the PB and PR signals for the chrominance. Color can be reproduced more faithfully with this system because each of these signals is independent. The component signal is also called the “color difference signal” because the luminance signal is subtracted from the color signal.
Specifications ■ RX-E810 AMPLIFIER SECTION • Minimum RMS output power per channel (6 Ω , 1 kHz, 0.1% THD) ......................................... 55 W + 55 W • Maximum RMS output power per channel (6 Ω , 1 kHz, 1% THD) ............................................ 65 W + 65 W • Input sensitivity/Impedance DVD/MD/TAPE/AUX etc. ..................................... 150 mV/47 kΩ • Frequency Response (20 Hz to 20 kHz) DVD etc. ........................................................................ 0 ± 0.
LASER Type Wave length CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT PRODUIT LASER DE CLASSE 1 Output Power Beam divergence Semiconductor laser GaAlAs 650 nm (DVD) 780 nm (VCD/CD) 7 mW (DVD) 10 mW (VCD/CD) 60 degrees CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
LIST OF REMOTE CONTROL CODES TV Admiral Aiwa Akai Alba AOC Bell & Howell Bestar Blaupunkt Blue sky Brandt Brocsonic Bush By Design Clatronic Craig Croslex Curtis Mathis Daewoo 292/293/216 294/276/283/284 295/296 296 297 292 298 229/222 298 223 297 296 201/202 298 224 225/298 297/226 297/298/224/227/ 228 Dayton 239 Dwin 293/281 Emerson 297/224/239/232 Ferguson 223/265/266 First line 298 Fisher 295/233 Fraba 298 Fujitsu 289 Funai 277/278 GE 293/297/234/235/ 236 Goodmans 296/298/223 Grundig 229/238/249 Hitac
03EN_MCR-E810_B_cv4.fm Page 2 Friday, September 1, 2006 5:00 PM © 2006 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD.
