yA~red Made for ~ iPod DiPhone DiPad
English FCC INFORMATION (for US customers) IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!: This product, when instal led as indicated in the instructions contained in this manua l, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
COMPL IANCE INFORMATION STATEMENT (DECLARATION OF CONFO RMITY PROCEDURE) Respons ible Party Address Yamaha Corporat ion of America A/ V Division 6600 Orangeth orpe Avenue, Buena Park, CA 90620, USA Telepho ne 1-714-522-9011 Type of Equipm ent Wireless Transmi tter for iPod Model Name YIT-Wl2 TX Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, MIS 3R I, Canada 1-416-298-1311 • This device complies with Part 15 ofthe FCC Rules and Industry Canada licenceexempt RSS standard( s).
in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Warranty policy for U.S. and Canada customer Your Yamaha product is covered by a limited warranty for one year from the date of purchase.
Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. Be sure to read the "Troubleshooting " section on common operating errors before concluding that this unit is faulty. 8 9 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Radio waves may affect electro-medical devices. Do not use this unit near medical devices or inside medical facilities.
About this manual • This manual describes all the "iPod'; "iPhone" and "iPad" as the "iPod'.' "iPod" refers to "iPod'; iPhone" and "iPad'; unless otherwise specified. • Marks used in this manual NOTE I This indicates precautions for use of the product and its feature limitations. HINT This indicates supplementary explanations for better use. yA~red The" y A~re d "and "yAired" are trademarks of Yamaha Corporation .
Introduction YIT-W12 consists of YIT-W12TX and a dedicated USB cable. YIT-W12TX is a wireless transmitter designed for iPod series and PCs. YIT-W12TX employs the Yamaha "yAired" technology to establish a wireless connection with another Yamaha product that supports "yAired" and enables playback of the iPod or PC on your Yamaha product. Also the supplied USB cable can be used for charging the iPod connected to the transmitter, or to play music or videos for an extended time.
Supplied items USB cable (0.3 m [1 ft]) * For connecting the transmitter to a PC (Be sure to use the supplied USB cable when connecting the transmitter to a PC.) Wireless transmitter (YIT-W12TX) Setting the group ID To establish a wireless connection (yAired) between the transmitter and another Yamaha product, you need to set both the products to the same group. Change the group ID of the transmitter or your Yamaha product if their group IDs are not same.
Playing back iPod music 1 Check that the transmitter and your Yamaha product are set to the same group ID. 2 Connec t your iPod to the transmitter. A wireless connection between the transmitter and your Yamaha product will be established.
Cha rgin g an iPod You can charge the iPod by connecting the transmitter to your PC using the supplied USB cable. Also, you can enjoy iPod music on your Yamaha product while charging the iPod. ·- I DODO DODD DODO 0 DODD @ I ..... J I II USB cable (supplied) "\ I \ \. NOTE • Charging may not be possible depending on the USB power supply capability of your PC. • Data synchronization between the iPod and PC may start automatically when they are connected.
3 Start playback on your PC. After a wireless connection between the transmitter and your Yamaha product is established, the Yamaha product automatically selects the transmitter (YIT) as the input source and starts to play the PC audio. \t:5':L mm m I 0 (lights up green) wireless connection established NOTE • The transmitter automatically stops if your Yamaha product is turned off or if an input source other than the transmitter is selected.
Troubleshooting Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, contact the nearest authorized Yamaha dealer or service center. First, check the following: CD The power cable of your Yamaha product is connected to an AC wall outlet securely. ® The latest firmware is installed on the transmitter or your iPod. Your iPod is not connected to the transmitter firmly.
There is a communication error between the transmitter and your iPod. (In this case, the red indicator starts flashing 30 seconds after an iPod connection.) Reconnect the iPod to the transmitter. If the problem happens frequently, disconnect the iPod from the transmitter, restart the iPod, andreconnecttheiPod No sound is C()IJling from the Yamaha product although a wireless connection is established. 8 The volume of your Yamaha product is too low. Turn up the volume.
•.. · ·.. < ·. . .. .• . . .. . . . .• .. ........ . . . . . . . .
Specifications Item Tr41nsmitt•r ('(IT,.W12TX) iPod touch (1st, 2nd, 3rd and 4th generation) Supported iPod/iPhone/iPad iPod nano (3rd, 4th, 5th and 6th generation) iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone (as of June 2012) iPad (3rd generation), iPad 2, iPad PC (Operating System) (as of June 2012) Windows 7, Windows Vista, Windows XP Power Consumption 0.3 W or less Allowable Current 2.
YAMAHA CORPORATION © 2012 Yamaha Corporation Printed in Malaysia ZE03990
