User`s manual

8 Operation of Digital Operator
8.2.2 Program Table Edit/Save (FnB03)
8-10
 LOOP: Number of Executions
Note: For details on the number of executions, refer to 6.1.4 (1) Program Table Functions.
 NEXT: PGMSTEP to be Executed Next
Note: For details on the PGMSTEP to be executed next, refer to 6.1.4 (1) Program Table Functions.
(4) Saving Program Tables
The operating procedure for saving program tables is shown below.
∗ If the key is pressed in an operation prohibited state, “Error.” is displayed for approximately 2 seconds and then
the display returns to the program table editing screen. In this case, make the setting again by referring to (1) Prepara-
tion.
㧸㧻㧻㧼㧜㧜㧜㧩㧜㧜㧜㧜㧝
㧸㧻㧻㧼㧜㧜㧜㧩㧜㧜㧜㧜㧝
Move cursor Change number of executions
㧸㧻㧻㧼㧜㧜㧜㧩㧜㧝㧜㧜㧝
㧺㧱㨄㨀㧜㧜㧜㧩㧜㧜㧜㧜㧜
㧺㧱㨄㨀㧜㧜㧜㧩㧜㧜㧜㧜㧜
Move cursor Change next PGMSTEP to be executed
㧺㧱㨄㨀㧜㧜㧜㧩㧜㧜㧞㧡㧡
If the value becomes less than 0,
“END” is displayed.
Step Display after Operation Keys Operation
1 Display the program table editing screen.
2
Press the key to view the program table save
operation screen.
3
Move the cursor with the keys to select
“STORE”.
Note: Selecting “CANCEL” and pressing the key
will return the display to the program table edit-
ing screen.
4
Press the key to start saving the program table to
flash memory.
*
Do not turn off the control power supply until saving
has been completed normally.
5
When saving to flash memory has been completed nor-
mally, the display returns to the program table editing
screen.
6
Press the key to return to the Utility Function
Mode main menu.
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧼㧻㧿㧜㧜㧜㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧝㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧞㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧟㧩㧿㨀㧻㧼
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㧼㧳㧹ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㧼㧳㧹ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧿㨠㨛㨞㨕㨚㨓ޓ㨚㨛㨣㧚㧚㧚
㧼㨘㨑㨍㨟㨑ޓ㨣㨍㨕㨠㧚
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧼㧻㧿㧜㧜㧜㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧝㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧞㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧟㧩㧿㨀㧻㧼
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧞㧜㧣ޓ㨂㧙㧹㨛㨚㨕㨠㨛㨞
㧲㨚㧮㧜㧟ޓ㧼㧳㧹ޓ㧱㨐㨕㨠
㧲㨚㧮㧜㧠ޓ㨆㧻㧺㧱ޓ㧱㨐㨕㨠
㧲㨚㧮㧜㧡ޓ㧶㧿㧼㧰ޓ㧱㨐㨕㨠