User`s manual

8 Operation of Digital Operator
8.2.3 ZONE Table Edit/Save (FnB04)
8-12
 Method for Moving the Cursor
The values within the frames in the figure below are the ZONE table numbers displayed at the digital operator.
∗ You can move 3 rows at a time by holding down the or key.
(3) Saving ZONE Tables
The operating procedure for saving ZONE tables is shown below.
7
Repeat steps 3 to 6 to set the ZONE table. On completing the setting of all the ZONE tables to be used, save the
ZONE tables to flash memory by following the procedure in (3) Saving ZONE Tables.
(cont’d)
Step Display after Operation Keys Operation
㪱㪦㪥㪜⇟ภ
ZONEP
㪱㪦㪥㪜㪥 㪱㪦㪥㪜⇟ภ
ZONEP
㪱㪦㪥㪜㪥
000NZ000PZ0000NZ000PZ0
100NZ100PZ1100NZ100PZ1
200NZ200PZ2200NZ200PZ2
300NZ300PZ3300NZ300PZ3
400NZ400PZ4400NZ400PZ4
500NZ500PZ5500NZ500PZ5
600NZ600PZ6600NZ600PZ6
31 ZP031 ZN031 31 ZP031 ZN031
㪱㪦㪥㪜⇟ภ
ZONEP
㪱㪦㪥㪜㪥
0 ZP000 ZN000
1 ZP001 ZN001
2ZP002ZN002
3ZP003ZN003
4ZP004ZN004
5ZP005ZN005
6 ZP006 ZN006
31 ZP031 ZN031
Moves the displayed rows up or down one row at a time.*
On reaching step 0, the next movement is to step 31.
On reaching step 31, the next movement is to step 0.
Moves the displayed
column one column
at a time to the left or
right.
On reaching the
edge of the table,
movement stops.
Step Display after Operation Keys Operation
1 Display the ZONE table editing screen.
2
Press the key to view the ZONE table save
screen.
3
Move the cursor with the keys to select
“STORE”.
Note: Selecting “CANCEL” and pressing the key
will return the display to the ZONE table editing
screen.
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㨆㧼㧜㧜㧜㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㨆㧼㧜㧜㧝㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㨆㧼㧜㧜㧞㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㨆㧼㧜㧜㧟㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㨆㧻㧺㧱ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㨆㧻㧺㧱ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱