User`s manual

8 Operation of Digital Operator
8.2.5 Program Table Initialization (FnB06)
8-16
8.2.5 Program Table Initialization (FnB06)
This function initializes the program tables and restores the settings on shipment from the factory.
(1) Preparation
The following conditions must be met to initialize the program table.
• The write-prohibited setting (Fn010) must not be set to write-protect parameters.
• The program must not be running or on hold.
• The program tables must not being saved by any other means than using the digital operator.
• The RES command must not being executed.
(2) Operating Procedure
∗ If the key is pressed in an operation prohibited state, “Error.” is displayed for approximately 2 seconds and then
the display returns to the FnB06 operation screen. In this case, make the setting again by referring to (1) Preparation.
Step Display after Operation Keys Operation
1
Press the key to open the Utility Function Mode
main menu, and move the cursor with the
keys to select FnB06.
2
Press the key to view the FnB06 operation screen.
3
Press the key to start program table initialization.
*
Do not turn off the control power supply until initial-
ization has been completed normally.
To cancel the FnB06 operation, press the key
before pressing the key. The display returns to the
Utility Function Mode main menu without executing
the operation.
4
When program table initialization has been completed
normally, “Done.” is displayed.
5
Press the key to return to the Utility Function
Mode main menu.
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧮㧜㧡ޓ㧶㧿㧼㧰ޓ㧱㨐㨕㨠
㧲㨚㧮㧜㧢ޓ㧼㧳㧹ޓ㧵㨚㨕㨠
㧲㨚㧮㧜㧣ޓ㨆㧻㧺㧱ޓ㧵㨚㨕㨠
㧲㨚㧮㧜㧤ޓ㧶㧿㧼㧰ޓ㧵㨚㨕㨠
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧵㨚㨕㨠㧙
ޓ㧿㨠㨍㨞㨠ޓ㧦㨇㧰㧭㨀㧭㨉
ޓ㧾㨑㨠㨡㨞㨚㧦㨇㧿㧱㨀㨉
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧵㨚㨕㨠㧙
㧾㨑㨟㨠㨛㨞㨕㨚㨓ޓ㨚㨛㨣㧚㧚㧚
㧼㨘㨑㨍㨟㨑ޓ㨣㨍㨕㨠㧚
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧵㨚㨕㨠㧙
㧰㨛㨚㨑㧚
㧼㨞㨑㨟㨟ޓ㨇㧿㧱㨀㨉ޓ㨗㨑㨥㧚
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧮㧜㧡ޓ㧶㧿㧼㧰ޓ㧱㨐㨕㨠
㧲㨚㧮㧜㧢ޓ㧼㧳㧹ޓ㧵㨚㨕㨠
㧲㨚㧮㧜㧣ޓ㨆㧻㧺㧱ޓ㧵㨚㨕㨠
㧲㨚㧮㧜㧤ޓ㧶㧿㧼㧰ޓ㧵㨚㨕㨠