User’ s Manual (English version) CNPS7700 Intel Pentium 4 Socket 775 CPU Grip (S-Type) Intel Pentium 4 Socket 478 CPU Grip (L-Type) Inner Hole AMD Sempron/AMD64 (Athlon 64/Opteron) Socket 754/939/940 CPU Grip (L-Type) Outer Hole * Applies to all versions of CNPS7700 LED. * Please read before installation. http://www.zalman.co.kr http://www.zalmanusa.
1. Features 1) Does not generate noise or vibration in Silent Mode. 2) Pure copper and/or pure aluminum base materials ensure excellent heat dissipation. 3) Intel Pentium 4 (Socket 775), Intel Pentium 4 (Socket 478), and AMD Sempron / AMD64 (Socket 754/939/940) compatible design for broad compatibility. 4) The large 120mm fan inside the FHS maximizes cooling performance by providing sufficient airflow even at slow rotation speeds.
4. Patents Korean Patent Application No. 00-54635 Korean Design Applications Nos. 04-16030 etc. Patent Applications pending in over 20 nations around the world, including USA, EU, and Japan Precautions 1) If excessive force is exerted on the fan, it may malfunction and result in damage to the product and/or the computer. 2) Do not put your finger in the fan while it is running. 3) Keep the product away from children. 4) Check the components list and condition of the product before installing.
6. Compatible CPUs 1) Intel Pentium 4 - Socket 775/478 All CPUs conforming to Socket 775/478 platform Cautions) ① No components higher than 39mm (possible examples : PSU, graphics card, RAM etc.) should be present within a 68mm radius from the center of the CPU. ② For Socket 478, as shown in Figure 2, a motherboard that is not compliant with the "10.2mm Motherboard component height restriction" standard, introduced by Intel, may create interference between components and the grip of CNPS7700.
7. Installation ※ CNPS7700 must be used with a grip specific to Socket each CPU socket. Refer to the table on the right to choose the correct grip for use. 775 S - Type Hole 478 L - Type Inner Hole 754/939/940 L - Type Outer Hole Grip Hole 1) Intel Pentium 4 - Socket 775 ① Install Clip Support for Socket 775 Align the clip support for socket 775 and the backplate for socket 775 with the mounting holes on the motherboard and fasten them together using the clip support fixing bolts.
2) Intel Pentium 4 - 478 ① Apply Thermal Grease Clean off particles and residue from the top of the CPU then spread a thin layer of the included thermal grease thoroughly on top of the CPU. CPU (IHS) ② Install Clip Supports for Socket 478 Install the clip supports for socket 478 on both sides of the retention guide as shown in the diagram. Retention Guide Clip Support for Socket 478 ③ Install Grips and Bolts Interlock the L-type grips with the clip.
3) AMD Sempron/AMD64 - 754/939/940 ① Fasten Nipples Place a small washer on the motherboard. Then, put a nipple over it and fasten the nipple until the Backplate for AMD64 is firmly attached to the motherboard on the opposite side of the CPU. * A Retention Guide is not necessary for installing CNPS7700 on Socket 754/939/940.
※FAN MATE 2 Installation and Usage 1) Installing FAN MATE 2 on the Inside of the System Fan Connector (CNPS7700) 2) Installing FAN MATE 2 on the Outside of the System Double-sided Tape FAN MATE 2 Motherboard Connect the appropriate 3-pin connector on the cable to the motherboard fan header and the CNPS7700’s fan connector. 6-Pin Connector Pull the 6-pin connector out of the system through the back and connect it to FAN MATE 2, which should be installed on the case using the included double-sided tape.
. Zalman Noise Prevention System When building a noiseless computer, use Zalman’s Noiseless Power Supply, Noiseless Case Fan, Fanless Northbridge Cooler, Heatpipe HDD Cooler, Heatpipe VGA Cooler, and Fan Controller to achieve stable performance and maintain a noiseless environment. Noiseless Power Supply Noiseless Case Fan Fanless Northbridge Cooler Heatpipe HDD Cooler Heatpipe VGA Cooler Fan Controller 10.