EN User manual Freezer ZFU20200WA
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 5 5 6 7 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 En
During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged. If the refrigerant circuit should become damaged: – avoid open flames and sources of ignition – thoroughly ventilate the room in which the appliance is situated • It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock.
• It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in the compressor. • Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation. • Wherever possible the back of the product should be against a wall to avoid touching or catching warm parts (compressor, condenser) to prevent possible burn.
3 Freezer baskets 4 Rating plate 5 Maxibox baskets Control panel 1 2 3 1 Alarm Light 2 Fast Freeze Indicator 3 Fast Freeze Switch 4 Pilot Light 5 Temperature Regulator Switching on Insert the plug into the wall socket. Turn the Temperature regulator clockwise to a medium setting. The Pilot light and the Alarm light will light up. Switching off To turn off the appliance, turn the Temperature regulator to the "0" position. Temperature regulation The temperature is automatically regulated.
Storage of frozen food When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours. The freezer drawers ensure that it is quick and easy to find the food package you want. If large quantities of food are to be stored, remove all drawers except for the bottom drawer which needs to be in place to provide good air circulation. On all shelves it is possible to place food that protrude until 15 mm from the door.
Helpful hints and tips Normal Operating Sounds • You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped through the coils or tubing. This is correct. • When the compressor is on, the refrigerant is being pumped around and you will hear a whirring sound and a pulsating noise from the compressor. This is correct. • The thermic dilatation might cause a sudden cracking noise. It is natural, not dangerous physical phenomenon. This is correct.
• clean the inside and accessories with lukewarm water and some neutral soap. • regularly check the door seals and wipe clean to ensure they are clean and free from debris. • rinse and dry thoroughly. Important! Do not pull, move or damage any pipes and/or cables inside the cabinet. Never use detergents, abrasive powders, highly perfumed cleaning products or wax polishes to clean the interior as this will damage the surface and leave a strong odour.
Problem The temperature in the freezer is too low. The temperature in the freezer is too high. There is too much frost. Possible cause Solution The product temperature is too high. Let the product temperature decrease to room temperature before storage. The room temperature is too high. Decrease the room temperature. The temperature regulator is not set correctly. Set a higher temperature. The Fast Freeze function is switched on. Refer to" Fast Freeze function".
Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Electrical Connection Caution! Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Warning! This appliance must be earthed.
3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4. Check that no cut, or stray strands of wire is present and the cord clamp E is secure over the outer sheath. 5. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 6. Switch on the appliance. The appliance is supplied with a 13 amp plug fitted B. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used.
2 1 • Stand the appliance upright. • Unscrew the handle (1) and fix it on the opposite side (2). • Re-insert the cover pins (3) on the opposite side. 1 3 Do a final check to make sure that: • All screws are tightened. • The edges of the doors run parallel to the side edge of the appliance. • The magnetic seal adheres to the cabinet. • The door opens and closes correctly. It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in the compressor.
www.zanussi.
www.zanussi.
www.zanussi.
280151036-A-492012 www.zanussi.