EN User manual Freezer ZFU719EW
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful Hints and Tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 5 5 6 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2. • • • • Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4. Do not pull the mains cable. 5. If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or fire. 6. You must not operate the appliance without the lamp cover (if foreseen) of interior lighting. This appliance is heavy.
Environment Protection insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked by the are recyclable. symbol This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials.
When switching on the freezer for the first time, the Red Alarm Indicator Light will blink until the internal temperature has reached a level required for the safe conservation of frozen food. Fast Freeze function If more than 3-4 kg of food is to be frozen: 1. Press the Fast Freeze Switch for 2-3 seconds to activate the fast-freeze function 6-24 hours before placing the fresh food in the freezer, the Yellow Fast Freeze Indicator Light will illuminate.
Helpful Hints and Tips Normal Operating Sounds • You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped through the coils or tubing. This is correct. • When the compressor is on, the refrigerant is being pumped around and you will hear a whirring sound and a pulsating noise from the compressor. This is correct. • The thermic dilatation might cause a sudden cracking noise. It is natural, not dangerous physical phenomenon. This is correct.
casing of this appliance is only cleaned with warm water with a little washing-up liquid added. After cleaning, reconnect the equipment to the mains supply. Defrosting the freezer A certain amount of frost will always form on the freezer shelves and around the top compartment. Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.
Problem Possible cause Solution The appliance is noisy The appliance is not supported properly Check if the appliance stands stable (all the four feet should be on the floor) The compressor operates continually The thermostatic control is set incorrectly Set a warmer temperature Doors are not shut properly or do not close tightly Check if the doors close well and the gaskets are undamaged and clean The door has been opened too frequently Do not leave the door open longer than necessary Large qu
Problem The appliance does not cool at all Possible cause Solution Plug is not connected to the mains socket properly Connect the mains plug properly There is no voltage in the mains sock- Call an electrician et (try to connect another appliance into it) Green indicator flashing The appliance is not switched on Switch on the appliance Temperature Regulator is not on Check the Temperature Regulator Temperature sensor problem Call the service personnel Closing the door 1. 2. 3.
1. 2. Fit the spacers into the holes. Make sure that the arrow (A) is positioned as shown in the picture. Turn counter-clockwise the spacers through 45° until they lock into place. must be at least 100 mm . Ideally, however, the appliance should not be positioned below overhanging wall units. Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet.
2 1 1. Remove the plug from the power socket. 2. Tilt back the appliance carefully so that the compressor cannot touch the floor. 3. Unscrew both adjustable feet. 4. Unscrew the screws of the door bottom hinge. 5. Take off the appliance door by pulling it slightly downwards. 6. Unscrew the top door hinge pin of the appliance then screw it back on the other side. 7. Fit the appliance door on the upper door hinge pin. 8. Remove the lower hinge. Put over the pin in the direction of the arrow. 9.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 1. Connect the wire coloured green and yellow to the terminal marked either with the letter “E“ or by the or coloured green and yellow. earth symbol 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3.
www.zanussi.
www.zanussi.
www.zanussi.
200384356-A-012012 www.zanussi.