GAS HOB MODEL ZGF 982 INSTRUCTION BOOKLET 2 Please read this instruction booklet before using the appliance
Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation ● This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. ● Any gas installation must be carried out by a registered CORGI installer. ● Remove all packaging before using the hob.
Contents For the User For the Installer Description of the Hob Technical Data Page 10 Page 5 Operation Page 6 Important Safety Requirements Page 11 Installation Page 12 Gas Connection Page 12 Building In Page 13 Electrical Connection Page 14 Wiring Diagram Page 15 Fault Finding Page 16 Commissioning Page 18 Conversion from natural gas to LPG Page 18 Maintenance and Cleaning Page 7 Something Not Working Page 8 Service and Spare Parts Page 8 Peace of Mind for 24 Months Pa
Description of the Hob 2 3 4 5 3 1 6 7 8 9 10 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Operation HOB BURNERS To light a burner, push the relevant control knob in, turn it anticlockwise to maximum position, and depress the ignition pushbutton marked by a small electric spark symbol. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table).
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Peace of Mind for 24 Months ZANUSSI GUARANTEE CONDITIONS We, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate.
Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner 860 mm. 510 mm. 72 mm. 12 Kg. Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. CUT OUT DIMENSIONS Width: 830 mm. Depth: 480 mm. Thickness: 30 mm. Ignition HT Spark Spark Generator Ispra Control's BF 50066 - 240V 0.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram.
Building In Building over a cupboard or drawer ON/OFF SWITCH 2 ON/OFF SWITCH 3 30 1 It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. a 60 FLEX OUTLET 20 min If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. b FLEX OUTLET FO 0763 FO 0764 FO 1013 Dimensions are given in mm.
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm.
Wiring Diagram L 1 A 2 0 3 220/240 4 5 6 B N A. IGNITOR SWITCH B.
Fault Finding Preliminary Electrical Systems Check PLUG (with cover removed) Brown Blue Green Yellow START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue ( ) E( ) FUSE Earth Wire Green/Yellow SOCKET (face view) N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? NO YES Carry out: D: Resistance to Earth check. Electricity supply should now be satisfactory. A.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check by pass simmer adjusted Check polarity and earth continuity of supply point Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from the tip of each electrode to the terminals 1 to 5 on the ignitor unit Check continuity fro
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN.