User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
• • • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
• • • • Do not touch the compressor or the condenser. They are hot. Do not remove or touch items from the freezer compartment if your hands are wet or damp. Do not freeze again food that has been thawed. Obey the storage instructions on the packaging of frozen food. INTERNAL LIGHT • The type of lamp used for this appliance is not suitable for household room illumination CARE AND CLEANING WARNING! Risk of injury or damage to the appliance.
DAILY USE WARNING! Refer to Safety chapters. FREEZING FRESH FOOD The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time. To freeze fresh foods it is not necessary to change the medium setting. However, for a faster freezing operation, turn the temperature regulator toward higher settings to obtain the maximum coldness. CAUTION! In this condition, the refrigerator compartment temperature might drop below 0°C.
• A faint click noise from the temperature regulator when the compressor switches on or off. HINTS FOR ENERGY SAVING • Do not open the door frequently or leave it open longer than absolutely necessary. • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator.
PERIODIC CLEANING CAUTION! Do not pull, move or damage any pipes and/or cables inside the cabinet. CAUTION! Take care of not to damage the cooling system. CAUTION! When moving the cabinet, lift it by the front edge to avoid scratching the floor. The equipment has to be cleaned regularly: 1. Clean the inside and accessories with lukewarm water and some neutral soap. 2. Regularly check the door seals and wipe clean to ensure they are clean and free from debris. 3. Rinse and dry thoroughly. 4.
WARNING! If you want to keep the appliance switched on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure. TROUBLESHOOTING WARNING! Refer to Safety chapters. WHAT TO DO IF... Problem Possible cause The appliance does not operate. The appliance is switched off. Switch on the appliance. The mains plug is not connected to the mains socket correctly. Connect the mains plug to the mains socket correctly. There is no voltage in the mains socket.
Problem Possible cause Solution Food products are not wrapped properly. Wrap the food products better. Temperature is set incorrectly. Refer to "Operation" chapter. The compressor does not start immediately after pressing the , or after changing the temperature. This is normal, no error has occurred. The compressor starts after a period of time. Water flows on the rear plate of the refrigerator. During the automatic defrosting process, frost melts on the rear plate. This is correct.
3. Replace the used lamp with a new lamp of the same power and specifically designed for household appliances (the maximum power is shown on the lamp cover). 4. Install the lamp cover. 5. Tighten the screw to the lamp cover. 6. Connect the plug to the mains socket. 7. Open the door. Make sure that the light comes on. CLOSING THE DOOR 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets.
5. Switch on the appliance. The appliance is supplied with a 13 amp fuse (B). In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4.
212001412-A-042016 WWW.ZANUSSI.