Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
![](/manual/zebra/105se/specifications-english/images/img-101.png)
Zebra S-Series User’s Guide 93
Print speed — The speed at which printing occurs. For thermal transfer
printers, this speed is expressed in terms of ips (inches per second). Zebra
offers printers that can print from 2 ips to 12 ips.
Printhead wear — The degradation of the surface of the printhead and/or
the print elements over time. Heat and abrasion can cause printhead wear.
Therefore, to maximize the life of your printhead, use the lowest print
darkness setting (sometimes called “burn temperature” or “head
temperature”) and the lowest printhead/toggle pressure necessary. Also,
use ribbon that is as wide or wider than the media to protect the printhead
from the rougher media.
Reflective media sensor — A sensor that detects a black mark on the back
of media by measuring the reflectivity of the media. This mark helps the
printer determine label size and print registration.
Registration — Alignment of printing with respect to the top of a label/
tag.
Ribbon — A band of inked material that is pressed by the printhead
against the media to transfer an image onto the media, which in turn is
pressed against the platen. A ribbon consists of a base film coated with
wax or resin “ink.” Zebra ribbons also have a back coating that protects
the printhead from damage. The ribbon transfers ink onto the media when
heated by the printhead.
Ribbon wrinkle — A wrinkling of the ribbon caused by improper
alignment of the strip plate and/or printhead pressure. This wrinkle can be
seen just above the strip plate. Ribbon wrinkle can cause voids in the print
and/or the spent ribbon to rewind unevenly. This is a condition that should
be corrected by performing adjustment procedures.
Roll media — Media that comes supplied rolled up on a core (usually
cardboard). Contrast this with fanfold media, which comes folded in a
rectangular stack.
Supplies — Supplies is a general term for ribbon and media.