Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
Zebra S-Series User’s Guide 97
R
Removing Used Ribbon (105Se), 19
Removing Used Ribbon (160S), 20
Repacking, 5
Reporting Damage, 7
Reshipping, 8
Rewind Mode, 17, 25
Ribbon
Loading (105Se), 11–13
Loading (160S), 14
Requirements, 4
Sensor Sensitivity, 63
Specifications, 73
Roll Media, 15
RS-232 Serial Data Port
DCE Devices, 48
DTE Devices, 48
Hardware Control Signal Descriptions, 47
Parallel Cabling Requirements, 49
Parallel Interface, 49
RS-232 Cabling Requirements, 47
Signal Descriptions, 50
S
Serial Number, 1
Signal Descriptions, 50
Site Requirements, 10
Specifications, 71–77
Storage, 8
System Components, 45
System Considerations
Communications Code, 45
Data Specifications, 46
Interfaces, 46
System Overview
Communication Capabilities, 2
Media Transport Mechanism Capabilities, 3
Print Mechanism Capabilities, 2
Thermal Transfer Printer Functions, 2
System Requirements, 3
T
Tear-Off Mode, 17, 24
Toggle Positioning, 59
Transmissive Media Sensor Position
Lower Transmissive Media Sensor, 62
Upper Transmissive Media Sensor, 61
Transmissive Sensing Mode, 24
Troubleshooting, 65
U
Unpacking, 7
V
Voltage Selection, 8
W
Warnings
230 VAC Operation, 4
Installation, 4
Repacking, 5
Ribbon and Printhead Wear, 5
Shielded Cable, 5
Z
ZebraNet Interface Option, 80
ZPL II Label Formats, 35–37
ZPL II Specifications, 73