Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
2 Warranty Statement
To qualify for this warranty, the printhead must be returned to the factory
or to an authorized service center. Customers are not required to purchase
Zebra supplies (media and/or ribbons) for warranty qualification.
However, if it is determined that the use of other manufacturer supplies has
caused any defect in the printhead for which a warranty claim is made, the
user is responsible for Zebra’s labor and material charges required to repair
the defect. The warranty becomes void if the printhead is physically worn
or damaged; also if it is determined that failure to follow the preventive
maintenance schedule listed in the User’s Guide has caused defect in the
thermal printhead for which a warranty claim is made.
Software
. Software is warranted to be free of defects in material and
workmanship for 30 days from the date of purchase. In the event of
notification within the warranty period of defects, Zebra will replace the
defective diskette or documentation.
Batteries
. Mobile printer batteries are warranted to be free of defects in
material and workmanship for 90 days from date of purchase. In the event
of notification within the warranty period, Zebra will replace the defective
battery provided there has not been damage resulting from user abuse.
6XSSOLHV3URGXFWV
Supplies are warranted to be free from defect in material and workmanship
for a period of six (6) months for media and twelve (12) months for ribbon
from the date of shipment by Zebra. This is provided the user has complied
with storage guidelines, handling, and usage of the supplies in Zebra
printers.
Zebra’s sole obligation under these warranties is to furnish parts and labor
for the repair or possible replacement of products found to be defective in
material or workmanship during the warranty period. Zebra may in its
discretion issue a credit for any such defective products in such amount as
it deems reasonable.