Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
8Zebra S-Series User’s Guide
6WRUDJHDQG5HVKLSSLQJ
If you are not placing the printer into operation immediately, repackage it
using the original packing materials. The S-Series Printer may be stored
under the following conditions:
• Temperature: –40° to +158° F (–40° to +70° C)
• Relative humidity: 20% to 85% non-condensing
Should it become necessary to ship your printer, remove any ribbon and
paper roll from the supply spools, otherwise damage to the printer could
result. Carefully pack the printer in a suitable container to avoid damage
during transit. Whenever possible, use the original container and
packaging material from the factory. If you use a different container, a
procedure similar to the original factory packaging should be followed.
&$87,21'RQRWSDFNDJHWKHSULQWHULQDULJLGFRQWDLQHU
ZLWKRXWXWLOL]LQJVKRFNPRXQWVRUVKRFNDEVRUELQJSDFNLQJ
PDWHULDO$ULJLGFRQWDLQHUDOORZVVKRFNRQWKHRXWVLGHWREH
WUDQVPLWWHGXQGDPSHGWRWKHXQLWZKLFKPD\FDXVHGDPDJH
3RZHU&RQQHFWLRQ
$&9ROWDJH6HOHFWLRQ3URFHGXUH
The S-Series Printer’s AC voltage may be set for either 115 VAC or 230
VAC operation. To match the printer’s power entry selection to the
available power source, refer to Figure 1 and follow the procedure outlined
below:
1. Locate the AC power area at the rear of the printer.
2. Using a small flatblade screwdriver or similar tool, move the voltage
selection switch to the 115 V or 230 V position as required. (The
initial position of the switch depends on how the printer was ordered.)
Make sure that the appropriate fuse is in place.