Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
Zebra S-Series User’s Guide 17
7HDU2II0RGH
Follow the instructions described in “Roll Media” on page 15.
5HZLQG0RGH
Note: Rewind option required.
To initially configure the printer for this mode, follow these steps:
1. Remove the media rewind plate from its storage location in front of
the printhead inside the media compartment.
2. Invert the rewind plate so that the lip on the attached hook plate points
down.
3. Insert the hook plate lip a short distance (1/2") into the lower opening
in the side plate.
4. Align the upper end of the rewind plate with the corresponding
opening in the side plate and slide the rewind plate in so that it stops
against the main frame.
5. Remove the hook from the take-up spindle shaft.
6. Route the media as shown in Figures 5 and 6 and wind it 1-2 times
around a 3" core.
3HHO2II0RGH
1. Remove the rewind plate if one is present and store it on the two
mounting screws on the inside of the front panel. Align the notch or
web in the media so that the take label sensor can sense a peeled label.
2. Load media as shown in Figures 5 and 6.
3. Remove the hook from the take-up spindle shaft.
4. Remove several labels from the media backing and then wind the
backing 1-2 times around the media take-up spindle and reinstall the
hook.