Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
32 Zebra S-Series User’s Guide
)(('.H\6HOI7HVW
Note: The CANCEL Key Self Test should be performed before this self
test. Information on the configuration printout (see Figure 12 on
page 30) can be used with the results of this self test to determine
the best darkness setting for a specific media/ribbon combination.
The FEED Key Self Test prints out at various darkness settings above and
below that of the darkness value shown on the configuration label. Inspect
these labels and determine which one has the best darkness setting for the
application. This value can be entered into the printer by setting the
darkness during the configuration procedure.
The value printed on the FEED
Key Self Test label is added to
(plus) or subtracted from
(minus) the “Darkness” value
specified on the configuration
label. The resulting numeric
value (0 to 30) is the best
darkness value for that specific
media/ribbon combination.
The darkness value can also be
programmed into the ZPL II
formats sent to the printer.
Figure 14