Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
![](/manual/zebra/105se/specifications-english/images/img-5.png)
Zebra S-Series User’s Guide v
yØÃAÏÍAcÍAOÃAÏ ³³³³³³³³³³³³³³³³³³³³³³³³³³³³Ñ
Option Switches.....................................................................................................39
Bank 1...............................................................................................................40
Bank 2...............................................................................................................41
Configuration Mode...............................................................................................42
Calibration ........................................................................................................43
Adjusting the Print Darkness............................................................................44
Adjusting the Media Rest Position ...................................................................44
Adjusting the Position of the Top of the Label.................................................44
ÏlÃYlYÏƳ³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³~{
System Components...............................................................................................45
System Considerations...........................................................................................45
Communications Code......................................................................................45
Interfaces...........................................................................................................46
Data Specifications ...........................................................................................46
RS-232 Serial Data Port.........................................................................................46
RS-232 Pinouts.................................................................................................46
Hardware Control Signal Descriptions.............................................................47
RS-232 Cabling Requirements .........................................................................47
Interconnect to DTE Devices............................................................................48
Interconnect to DCE Devices ...........................................................................48
Parallel Cabling Requirements .........................................................................49
Parallel Interface...............................................................................................49
Signal Descriptions...........................................................................................50
-ÃlÞlÏÞlÍ"AÏlAYl ³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³{¦
Overview................................................................................................................51
Cleaning.................................................................................................................51
Exterior Surfaces ..............................................................................................51
Interior ..............................................................................................................51
Printhead and Platen Roller ..............................................................................52
Media, Ribbon, and Label Available Sensors ..................................................57
Cutter Module...................................................................................................57
Lubrication.............................................................................................................58