Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
54 Zebra S-Series User’s Guide
Extend the Life of Your Printhead
With Save-A-Printhead Cleaning Film
Challenge
The printhead is the most critical component in your printer, and possibly the most
delicate. It is a consumable item just like the brakes on your car, which eventually
wears over time. However, with ongoing careful attention and maintenance, you can
extend the life of the printhead!
Below are photographs of three printheads. The first printhead is brand new. The
second has printed over 1 million linear inches of thermal transfer labels and has been
properly maintained. The third printhead has printed far fewer labels, but without
proper care and maintenance, signs of abrasion and contamination build-up are
evident.
Preventive Maintenance
For optimum performance, clean the printhead regularly after every roll of thermal
transfer ribbon or after every roll of direct thermal labels. Take care when handling or
cleaning the printhead by removing any jewelry that may scratch the printhead and
use a grounding strap or anti-static mat to discharge static electricity that could
damage the printhead.
To start, only use the pre-soaked (isopropyl alcohol) cleaning swabs provided in the
preventive maintenance kit. First, turn off the printer and open the printhead. Lightly
blow or brush away any loose dust and lint particles within the print mechanism (i.e.,
rollers, media/ribbon sensors, and printhead). NEVER use any hard, metallic, or
abrasive objects — such as a screwdriver — to remove adhesives or other
contaminants that may have built up on the printhead.
Next, press the swab tip against the printhead and swipe the print elements from end to
end. Then, turn the platen rollers while wiping them from side to side. Repeat this
step until the swab no longer shows dirt.
New
Over 1 Million Inches
(Properly Maintained)
Less Than 1 Million Inches
(Without Proper Care)