Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
72 Zebra S-Series User’s Guide
0HGLD+DQGOLQJ
• Tear-Off Mode: Produced in strips.
• Peel-Off Mode: Requires Peel-Off option or Media Rewind option.
Labels are dispensed and peeled from the liner, and the liner is rewound
internally.
• Rewind Mode: Requires Media Rewind option. A full roll of printed
labels is rewound internally.
• Cutter Mode: Requires Cutter Module option. Media cut after
printing; under software control.
0HGLD
Media Specifications 105Se 160S
Total media width
Maximum 4.5" 114.3 mm 7.2" 182.9 mm
Minimum 0.75" 19.05 mm 2.0" 50.8 mm
Label length
Maximum Refer to “Printing Considerations” on page 71.
Minimum
Tear-Off 0.63" 16.00 mm 0.63" 16.00 mm
Peel-Off 0.50" 12.8 mm 0.50" 12.8 mm
Rewind 0.50" 12.8 mm 0.50" 12.8 mm
Cutter 1.25" 31.75 mm N/A N/A
Total thickness
(includes liner)
Maximum (Printhead
position may need to be
adjusted above 0.01”)
0.015" 0.381 mm 0.015" 0.381 mm
Minimum 0.0023" 0.0584 mm 0.0023" 0.0584 mm
Core size 3.0" 76.2 mm 3.0" 76.2 mm
Maximum roll diameter 8.0" 203.2 mm 8.0" 203.2 mm
Interlabel gap (0.115”/3 mm preferred) 0.079" - 0.157" 2 mm - 4 mm 0.079" - 0.157" 2 mm - 4 mm
Maximum internal fanfold media pack size
(L x W x H)
8.0" x 7.2" x
6.2"
203.2 mm x 182.8
mm x 157.4 mm
8.0" x 7.2" x
6.2"
203.2 mm x 182.8
mm x 157.4 mm
Additional Specifications for Black Mark Media (optional on 105Se)
Mark thickness (measuring
parallel to label/tag edge)
Minimum 0.12" 3 mm 0.12" 3 mm
Maximum 0.43" 11 mm 0.43" 11 mm
Mark width (measuring
perpendicular to label/tag edge)
Minimum 0.43" 11 mm 0.43" 11 mm
Maximum Full media width. Full media width.
Mark-to-mark registration tolerance +/-0.016" +/-0.4 mm +/-0.016" +/-0.4 mm
Mark location Mark must be located on the inside of the media (closest to the printer’s
mainframe when loaded in the printer).
Mark density >1.0 ODU (Optical Density Unit)
Density of the back of the media on which the
black mark is printed
0.5 ODU maximum