Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
Zebra S-Series User’s Guide 73
5LEERQ
=HEUD3URJUDPPLQJ/DQJXDJH,,=3/,,
%DU&RGHV
Ribbon Width
105Se 160S
Zebra recommends using ribbon
at least as wide as the media
you are using to protect the
printhead from wear.
Maximum 4.33" 110 mm 6.89" 175 mm
Minimum 0.94" 24 mm 2.0" 51 mm
Standard
lengths
2:1 media to ribbon roll ratio 984 ft. 300 m 984 ft. 300 m
3:1 media to ribbon roll ratio 1476 ft. 450 m 1476 ft. 450 m
Roll size Inner diameter of core 1.0" 25.4 mm 1.0" 25.4 mm
Outside diameter of full roll of ribbon 3.2" 81 mm 3.2" 81 mm
• Downloadable graphics with data compression • Communicates in printable ASCII characters
• Bit image data transfer and printing, including mixing of
text and graphics
• Controlled by a mainframe, minicomputer, PC, or other
data entry device
• Format inversion • Serialized fields
• Mirror image printing • In-Spec OCR-A and OCR-B
• UPC/EAN (nominal 100% magnification [6 dots/mm and
12 dots/mm only])
• Four-position field rotation (0°, 90°, 180°, 270°)
• Bitmap and scalable fonts
• Programmable quantity with print pause
• Code 11, Code 49, Code 93 • UPC-A
• Code 39 (supports ratios of 2:1, 3:1, 5:2, 7:3) • PDF 417
• Interleaved 2 of 5 • POSTNET
• CODABAR (supports ratios of 2:1, 3:1, 5:2) • MSI
• Industrial 2 of 5, Standard 2 of 5 • E/EAN-8, E/EAN-13, EAN EXTENSIONS
• Plessey • DataMatrix
• Code 128 (supports serialization in subsets B and C and
UCC Case C Codes)
• MAXICODE