Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
![](/manual/zebra/105se/specifications-english/images/img-88.png)
80 Zebra S-Series User’s Guide
)DQIROG6XSSO\%LQ
Your printer may be equipped with an optional internal fanfold supply bin.
It is used to load fanfold media within the media compartment, and it
protects the media from environmental contaminants such as dust and dirt.
The fanfold media supply bin is fully adjustable. It accommodates media
from 1.57" (40 mm) to 3.54" (90 mm) wide (7.17" [183 mm] wide for the
160S) and 3.5" (89 mm) to 8" (203mm) long. The maximum stack height
for 8" long media is 4.5". Stack heights of 6.5" may be achieved with
media less than 3.5" long.
The fanfold supply bin may be installed in the field by the operator. To
install the fanfold supply bin, follow the instructions included with the
option.
Note: The fanfold supply bin, peel-off option, and rewind option are
mutually exclusive. The fanfold supply bin may not be installed
in S-Series Printers with the peel-off option or the rewind option.
Fanfold media may be used with the rewind spindle installed by
using one of the external fanfold supply access slots (at the
bottom and rear of the printer).
([WHUQDO=HEUD1HW(WKHUQHW,QWHUIDFH
ZebraNet allows you to connect your printer to your ethernet network.
This interface option is available for both 10Base-2 and 10Base-T
networks.
%ODFN0DUN5HIOHFWLYH6HQVRU
Note: For the 105Se printer only.
The reflective sensor utilizes continuous media with black marks printed
on the back of the label liner. The black mark sensor determines the label
length and the top of the label by detecting the black mark (similar to the
way a transmissive sensor detects the gap or notch).
This option is in addition to the standard transmissive sensor and is
software- or switch-selectable.