Specifications
Table Of Contents
- Introduction 1
- Installation 7
- Operation 23
- Configuration and Calibration 39
- Interconnections 45
- Preventive Maintenance 51
- Adjustments 59
- Troubleshooting 65
- Specifications 71
- Options 79
- Appendix 83
- Glossary 91
- Index 95
- Communication Capabilities
- Thermal Transfer Printer Internal Functions
- Print Mechanism Capabilities
- Media Transport Mechanism Capabilities
- Installation
- 230 VAC Operation
- Use of Shielded Cable
- Ribbons and Printhead Wear
- Repacking
- AC Voltage Selection Procedure
- AC Power Fuse Replacement
- 115 VAC Operation
- 230 VAC Operation
- Roll Media
- Tear-Off Mode
- Rewind Mode
- Peel-Off Mode
- Cutter Mode
- Fanfold Media
- Media Sensing Modes
- Media Transport Modes
- PAUSE Key
- FEED Key
- CANCEL Key
- MODE Key
- Introduction
- CANCEL Key Self Test
- PAUSE Key Self Test
- FEED Key Self Test
- FEED Key and PAUSE Key Self Test
- MODE Key Self Test
- PAUSE Key and CANCEL Key Self Test
- FEED Key and CANCEL Key Self Test
- Format 1: Simple Text and a Barcode
- Format 2: Saving a Label Format as a Graphic Image
- Format 3: Using a Serialized Data Field
- Bank 1
- Bank 2
- Calibration
- Adjusting the Print Darkness
- Adjusting the Media Rest Position
- Adjusting the Position of the Top of the Label
- Communications Code
- Interfaces
- Data Specifications
- RS-232 Pinouts
- Hardware Control Signal Descriptions
- RS-232 Cabling Requirements
- Interconnect to DTE Devices
- Interconnect to DCE Devices
- Parallel Cabling Requirements
- Parallel Interface
- Signal Descriptions
- Exterior Surfaces
- Interior
- Printhead and Platen Roller
- Media, Ribbon, and Label Available Sensors
- Cutter Module
- Upper Transmissive Media Sensor Position Adjustment
- Lower Transmissive Media Sensor Position Adjustment
- Printing Considerations
- Print Speeds
- Media Handling
- Media
- Ribbon
- Zebra Programming Language II (ZPL II®)
- Bar Codes
- Standard Fonts
- Physical
- Electrical
- Communications Interface
- Environmental Ranges
- Options and Accessories
- Label Darkness Levels
- A
- B
- C
- D
- F
- I
- L
- M
- O
- P
- Parallel Cabling Requirements, 49
- Parallel Interface, 49
- PAUSE Key and CANCEL Key Self Test, 33
- PAUSE Key Self Test, 31
- PAUSE Key, 26
- Peel-Off Mode, 17, 25
- Peel-Off Option, 79
- Power Connection
- Power Cord, 83
- Power-On Self Test, 28
- Preventive Maintenance, 51
- Print Darkness, 44
- Printer Diagnostics, 34
- Printer Operating Modes
- Printer Power Up, 21
- Printer Self Tests
- Printer Specifications
- Printhead DPI Option, 82
- Printhead Pressure Adjustment, 59
- R
- S
- T
- U
- V
- W
- Z
![](/manual/zebra/105se/specifications-english/images/img-96.png)
88 Zebra S-Series User’s Guide
2SWLRQDO3ULQWHU)RQWV
Your printer can be optioned with character fonts in addition to those that
are standard in the unit. The following pages illustrate the optional fonts
in each of the available styles. From time to time, additions may be made
to the list of available fonts. Contact Zebra Technologies Corporation or
your sales representative for further information.
Only one additional font can be installed in the printer at a time. This
installation should be performed by a service technician. Once installed,
this font can be used in addition to the standard fonts available in the
printer. Refer to the ZPL II Programming Guide for further application
information.
Once an optional font is installed in the printer, the configuration label
printed during the CANCEL Key Self Test indicates the font type as the
“Socket 2 ID”.
:KHQHTXLSSHGZLWKWKH%LWPDS&*7ULXPYLUDWH%ROG&RQGHQVHGIRQWWKH
6HDQG6KDYHWKHVDPHIRQWVW\OHVDVWKH6WULSH
6SULQWHU
Optional Printer Fonts Currently Available
Scalable Smooth Fonts (each is supplied as a
complete set of Normal, Bold, Italic, and Bold
Italic styles)
Bitmap Smooth Fonts (supplied only in Bold).
Type sizes: 6 pt, 8 pt, 10 pt, 12 pt, 14 pt, 18 pt,
24 pt
CG Triumvirate™ CG Triumvirate™
— CG Triumvirate™ Condensed
CG Times™ CG Times™
CG Palacio™ CG Palacio™
Futura™ Futura™
Univers
®
Univers
®