Operation Manual
32 CKE850-001_v01
6
On/off lever (on-off)
7
Handle
8
Anti-deposit lter
9
Storage space for the connecting cord
Preparation of the electric kettle for
operation
Before the rst use, wash the kettle inside
(for washing instructions see “Cleaning and
maintenance”),llitwithwateruptothe“max”
level,andletitboilfourtimes(usefreshwater
eachtime)andwashagain.
Operating instructions of the electric kettle
(Fig. B)
1
Press the lid button (5) – the kettle lid will open.
2
Place the lter (8) in the kettle – if it was taken out
before.
3
Fill the kettle up with the desired amount of water (the
level is visible on the indicator (3)).
Donotboilthewaterifitisbelowtheminimum
level or beyond the maximum level on the
indicator(3).
4
Close the lid.
5
Place the kettle on the power base (4).
6
Put the plug of the connecting cord into a mains socket with
an earth pin – the upper part of the kettle body will light up.
7
Turn the kettle on by pressing the lever (6) – the indicator
light will come on.
8
The kettle switches off automatically when the water
has reached the boiling point, the lever switch returns to its
starting position – the light comes off.
If further use of the kettle is anticipated, it is not necessary
to remove the plug of the connecting cord from the power
socket.
Becarefulnottollupwithwaterbeyondthe
nominalcapacitywhenpouringwaterintothe
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the lter
slowing down the speed of the ow. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched on, it will be
switched off by a thermal device automatically.
In order to switch the kettle on again after it has cooled down
(approx. 15 minutes), take it off the base, replace it and
switch the kettle on by pressing the lever (6). The cooling
down of the kettle can be accelerated by puring cold water
into the kettle.
Cleaning and maintenance (Fig. C)
Alwayscleanacoldkettle!
1
Remove the plug of the connecting cord from the power
socket.
2
Remove lter (8) and rinse it under running water.
3
Clean the outside surfaces with a soft cloth moistened
with washing-up liquid.
In order to remove the build-up of hard water lm from the
outside and inside walls of the kettle, wipe them with a cloth
moistened with vineger.
4
Rinse the kettle with fresh water.
Descaling
In the event that scale builds up on the bottom of the kettle,
it needs to be removed. 6% or 10% vinegar is used for this
purpose.
Open the lid
●
(5).
Take out the lter
●
(8).
Wash the lter under running water.
●
Pour in 0.5 l of vinegar and switch on the kettle
●
(6).
Boil the vinegar and leave in the kettle for about 30
●
minutes.
Pour the vinegar out and rinse the kettle with fresh
●
water.
Fill the kettle up with fresh water, boil the water and pour
●
it out after is has boiled.
Repeat the above procedure if there still is scale on the
●
bottom.
When the procedure is nished, replace the ter
●
(8) in
the kettle, following the procedure of taking the lter out
in reverse order.
Negligenceindescalingthekettlemayresults
initsdamage.
Ecology – environment protection
Each user can protect the natural environment. It is neither
difcult nor expensive.
In order to do it: put the cardboard packing into
recycling paper container; put the polyethylene
(PE) bags into container for plastic.
When worn out, dispose the appliance to
particular disposal centre, because of the
dangerous elements of this appliance, which
can be hazardous for natural environment.
Donotdisposeintothedomesticwastedisposal!!!
The manufacturer/importer does not accept any liability for any
damages resulting from unintended use or improper handling.
The manufacturer/importer reserves his rights to modify the product
any time in order to adjust it to law regulations, norms, directives,
or due to construction, trade, aesthetic or other reasons, without
notifying in advance.