Use, Care, and Installation Guide www.zephyronline.com Verona ZVO-E30AG ZVO-M90AG + Model number: Serial Number: JUL12.
www.zephyronline.
INSTALLATION Ducting Calculation Sheet ....................................... Mounting Height & Clearance................................ Ducting Options ........................................................... Hood Specifications ................................................... Mounting the Range Hood ...................................... Ductless Recirculating .............................................. 5 6 7 8 9 10 FEATURES & CONTROLS Touch Controls ..........................................
www.zephyronline.com Important Safety Notice READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. b.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing.
List of Materials www.zephyronline.com MODELS: ZVO-E30AG & ZVO-M90AG PARTS SUPPLIED 1 - Hood with internal blower 2 - Aluminum mesh filters 1 - Duct cover assembly (top and bottom) 1 - Duct cover wall bracket 3 - 3W Zephyr Bloom® LED light bulbs (pre-installed) 1 - 8” round backdraft damper (pre-installed) 1 - Hardware package HARDWARE PACKAGE CONTENTS M3.
Equivalent number length x used = Duct pieces Total Total 3-1/ 4” x 10” 1 Ft. Rect., straight x( ) = Ft. 6”- 8” Round 30 Ft. wall cap with damper x( ) = Ft. 7” Round, straight 1 Ft. x( ) = Ft. 6”- 8” Round, 30 Ft. roof cap x( ) = Ft. 8” Round, straight 1 Ft. x( ) = Ft. 6” round to 1 Ft. 3-1/ 4” x 10” rect. transition x( ) = Ft. 3-1/ 4” x 10” 15 Ft. Rect. 90 0 elbow x( ) = Ft. x( ) = Ft. 3-1/ 4” x 10” 9 Ft. Rect. 45 0 elbow x( ) = Ft. 6” round to 16 Ft.
Installation – Mounting Height & Clearance www.zephyronline.com ALWAYS, when possible, reduce the number of transitions and turns. If a long duct run is required, increase duct size from 8” to 10”. If turns or transitions are required: Install as far away from duct opening and as far apart between the two transitions as possible. A n. mi . B n i m .C x ma D n. mi . E n mi . F x ma Minimum mount height between range top to hood bottom should be no less than 26”. in. ” m x.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.
front of hood side of hood 12 13/16” 12 13/16” 7 13/16” 11 15/16” Z1C-00VO min. ducted - 41 1/2” min. recirc. - 46” max. - 80” 2 5/8” 14 1/4” STANDARD min. ducted - 26 1/2” min. recirc. - 31” max. - 50” 23 3/16” 22 1/16” 29 5/16”, 35 7/16” 4 1/8” top of hood 6 1/16” Installation – Hood Specifications www.zephyronline.
1. Measure from range top to hood bottom and mark line A. (26” minimum from range top) . 2. Plum and mark center line. 3. Mark mounting height line B. (14 3/4” from line A) 4. Mark mounting spread from C/L. (11 1/8”) 5. Fasten (2) M6 x 1-1/2” screws into studs on line B but do not tighten all the way. Note: Wood blocking may need to be added behind the drywall if no studs are present. Wall anchors may also be used but check local codes for compliance.
Installation – Ductless Recirculating www.zephyronline.com Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and filtered by a set of optional charcoal filters. The air is then purified and recirculated back within the home.
5 Display (speed level, delay off, filter clean/change,clean air) Lighted Glass Button clean mesh filter clean air replace charcoal filter Adjust 6 Speed Levels Lights On/Dim/Off 1 Power / Delay Off Button Power Button Function Button will turn power on and off for entire hood (fan and lights). - Hood will remember the last speed and light level it was turned off at. (Example: Press Button to turn off hood when on fan speed 4 and high lights.
Features & Controls – User Interface www.zephyronline.com Mesh Filter Clean Indicator (always enabled) - After 30 hours of fan usage the Graphic and words “clean mesh filter” will illuminate indicating it is time to clean the mesh filters. Graphic and words will remain illuminated until reset. - To reset: With hood off, hold the Button for three seconds, after three seconds the Graphic and words “clean mesh filter” will turn off and the 30 hour timer will reset.
Clean the hood surface periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain. Do not use any product containing chlorine bleach.
Troubleshooting www.zephyronline.com TROUBLESHOOTING PROCEDURES FOR VERONA WALL Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The wires on the control board are loose. 3. Make sure the wires on the control board are connected properly.
Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to control the maximum blower CFM of hoods with Zephyr’s DCBL Suppression System without the need for expensive make up air kits. ACT enables the installer to easily set the maximum blower speed to one of three most commonly specified CFM levels; 590, 440 or 290 CFM. The usage of ACT may not be necessary for your installation. Please check your local codes for CFM restrictions.
Fan Curve Diagrams www.zephyronline.
Wiring Diagram Power consumption shown for default 715 CFM blower configuration ACT 590 CFM - Fan Max. 130W @ 1.8A ACT 440 CFM - Fan Max. 70W @ 1A ACT 290 CFM - Fan Max. 35W @ .
List of Parts & Accessories www.zephyronline.com DESCRIPTION PART# Replacement Parts Light Bulb 3W LED (each) Aluminum Mesh Filter (each) Z0B-0032 50200045 Optional Accessories Recirculating Kit Replacement Charcoal Filter Duct Cover Extension ZRC-00VO Z0F-C002 Z1C-00VO To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.
STAPLE YOUR RECEIPT HERE Proof of the original purchase date is needed to obtain service under warranty Limited Warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-880-8368 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows: Three Year Limited Warranty
Guide d’utilisation, d’entretien et d’installation www.zephyronline.com Verona ZVO-E30AG ZVO-M90AG Numéro de modèle : _________________ Numéro de série : _________________ + JUL12.
www.zephyronline.
INSTALLATION Feuille de calcul pour le conduit ........................... Espace libre et hauteur de montage ................... Options d’installation pour le conduit .................. Spécifications de la hotte......................................... Montage de la hotte ................................................... Reprise d’air sans conduit ....................................... 5 6 7 8 9 10 COMMANDES Commandes à effleurement .................................. 11 Interface utilisateur .......
Mise en garde de sécurité LISEZ ET CONSERVEZ CES INSTRUCTIONS www.zephyronline.com AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’UTILISEZ PAS CET APPAREIL AVEC UN TABLEAU DE COMMANDE À SEMI-CONDUCTEURS. AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE BLESSURE, RESPECTEZ CES CONSIGNES : a. N’utilisez cet appareil que de la manière prévue par le fabricant. Si vous avez des questions, communiquez avec le fabricant. b.
POUR RÉDUIRE LES RISQUES D’INCENDIE, N’UTILISEZ QUE DES CONDUITS D’AÉRATION EN MÉTAL. ATTENTION Pour réduire les risques d’incendie et pour évacuer l’air convenablement, assurez-vous de canaliser l’air à l’extérieur de la maison. N’installez pas l’échappement du conduit dans les espaces entre les murs, le plafond, le grenier, les vides sanitaires ou le garage. FONCTIONNEMENT Laissez toujours les grilles de sûreté et les filtres en place.
Liste du matériel www.zephyronline.
Equivalent number length x used = Duct pieces Total Total 3-1/ 4” x 10” 1 Ft. Rect., straight x( ) = Ft. 6”- 8” Round 30 Ft. wall cap with damper x( ) = Ft. 7” Round, straight 1 Ft. x( ) = Ft. 6”- 8” Round, 30 Ft. roof cap x( ) = Ft. 8” Round, straight 1 Ft. x( ) = Ft. 6” round to 1 Ft. 3-1/ 4” x 10” rect. transition x( ) = Ft. 3-1/ 4” x 10” 15 Ft. Rect. 90 0 elbow x( ) = Ft. x( ) = Ft. 3-1/ 4” x 10” 9 Ft. Rect. 45 0 elbow x( ) = Ft. 6” round to 16 Ft.
Installation – Espace libre et hauteur de montage www.zephyronline.com possible l’un de l’autre. La hauteur de montage minimale ne devrait pas être moins de 26”. La hauteur de montage maximale ne devrait pas outrepasser 34”. A n. mi . B n i m .C x ma D n. mi . E n mi . F x ma Il est important d’installer la hotte à la hauteur de montage adéquate.
N’évacuez ou ne terminez JAMAIS l’échappement du conduit dans les espaces entre les murs, les vides sanitaires, le plafond, le grenier, ou le garage. Tous les échappements doivent être dirigés à l’extérieur de la maison, à moins que l’option de reprise d’air ne soit utilisée. N’utilisez que des conduits en métal pour cloison simple. Fixez toutes les pièces du conduit avec des vis à tôle et isolez tous les joints avec du ruban adhésif en toile ou du ruban réflecteur certifié.
Devant de la hotte Côté de la hotte 12 13/16” 12 13/16” Z1C-00VO Min. avec conduit - 41 1/2” Min. avec reprise d’air - 46” max. - 80” 2 5/8” 7 13/16” STANDARD Min. avec conduit - 26 1/2” Min. avec reprise d’air - 31” max. - 50” 14 1/4” 11 15/16” 23 3/16” 22 1/16” 29 5/16”, 35 7/16” 4 1/8” Dessus de la hotte 6 1/16” Installation – Spécifications de la hotte www.zephyronline.
1. Prenez la mesure entre la surface de la cuisinière et la base de la hotte; marquez la ligne A (min. 26” à partir du dessus de la cuisinière). Support pour le recouvrement du conduit 11 1/8” 2. Marquez la ligne centrale avec exactitude. 3. Marquez la ligne de hauteur de montage B (à 14-3/4” de la ligne A). 4. Marquez la largeur de montage à partir de la L/C (11-1/8”). 14 3/4” 5. Fixez (2) vis M6 x 1-1/2” aux poutres de la ligne B. Ne tournez pas les vis jusqu’au fond.
Installation – Reprise d’air sans conduit www.zephyronline.com La configuration de reprise sans conduit a été conçue pour les applications où il est impossible d’installer un conduit d’aération. Lorsque transformée, la hotte fonctionne comme une hotte de reprise d’air plutôt que comme un système d’évacuation d’air. Les vapeurs et fumées de cuisson sont aspirées et filtrées par un ensemble optionnel de filtres à charbon. L’air est ensuite purifié et redirigé à l’intérieur de la maison.
Touche de verre illuminé clean mesh filter clean air replace charcoal filter Choix de six vitesses Lumières : Allumer/ Veilleuse/Éteindre 1-Touche de mise en marche/arrêt automatique Fonction de mise en marche - La touche permet d’allumer et d’éteindre la hotte (ventilateur et lumières).
Commandes – Interface utilisateur www.zephyronline.com Indicateur de nettoyage des filtres à tamis (toujours en fonction) - Après 30 heures d’utilisation du ventilateur, le symbole et les mots « clean mesh filter » s’illuminent, indiquant qu’il est temps de nettoyer les filtres à tamis. Le symbole et les mots restent illuminés jusqu’à la réinitialisation de la fonction. - Pour réinitialiser : Lorsque la hotte est éteinte, appuyez et tenez la touche enfoncée pendant trois secondes.
Nettoyez régulièrement les surfaces de la hotte avec de l’eau savonneuse chaude et un chiffon de coton propre. N’utilisez pas de détergent abrasif ou corrosif, de laines d’acier ou de tampons à récurer; ils égratigneront et endommageront les surfaces. Pour les taches plus tenaces, utilisez du produit dégraissant liquide. Après le nettoyage, vous pouvez polir les surfaces avec des produits de polissage à acier inoxydable non abrasifs pour redonner de l’éclat et du lustre aux surfaces.
Dépannage www.zephyronline.com PROCÉDURES DE DÉPANNAGE POUR LA HOTTE VERONA WALL Problème Cause Solution Après l’installation, l’appareil ne fonctionne pas. 1. Le bloc d’alimentation n’est pas allumé 1. Assurez-vous que l’alimentation du disjoncteur et de l’appareil est allumée 2. La ligne électrique et le raccord de câble ne sont pas correctement branchés 2. Vérifiez que le branchement de l’appareil a été fait correctement 3.
Par défaut, le CFM maximale du le ventilateur est réglé à 715. Pour vérifier si votre installateur a permis ACT; Avec le hotte désactivé, appuyez et maintenez le bouton d’alimentation pendant trois secondes. Le CFM du le ventilateur sera affiché sur l’écran LCD. Il y a devrait également être une étiquette feuille d’aluminium situé à l’intérieur du corps de la hotte à proximité de la schéma de câblage qui indique le CFM du le ventilateur.
Tableau De Rendement Du Ventilateur www.zephyronline.
Modèle : Tension : Consommation d’énergie DEL DEL DEL DEL BRANCHEMENT DES COMMANDES DEL Lampe : Ventilateur : Verre : CCI DES DEL INTERRUPTEUR CCI DES DEL CCI DES DEL PROTÉGÉ THERMIQUEMENT Consommation montré pour défaut de configuration du ventilateur 715 CFM ACT 590 CFM - Ventilateur Max. 130W @ 1.8A ACT 440 CFM - Ventilateur Max. 70W @ 1A ACT 290 CFM - Ventilateur Max. 35W @ .
Listes des pièces et des accessoires www.zephyronline.com NO DE PIÈCE DESCRIPTION Pièces de remplacement Ampoule DEL 3W (chaque) Filtre à tamis en aluminium (chaque) Z0B-0032 50200045 Accessoires optionnels Ensemble de reprise d’air Filtre à charbon de remplacement Ensemble de prolongement de recouvrement de conduit ZRC-00VO Z0F-C002 Z1C-00VO Pour commander des pièces, visitez-nous en ligne au www.zephyronline.
AGRAFEZ VOTRE REÇU ICI Garantie limitée Une preuve de la date d’achat originale est nécessaire pour obtenir du service lorsque le produit est sous garantie POUR OBTENIR DU SERVICE SOUS GARANTIE OU POUR TOUTE QUESTION LIÉE À L’ENTRETIEN, veuillez communiquer avec nous au 1-888-880-8368 Zephyr Corporation (désigné aux présentes sous le nom de « nous ») garantit au premier acheteur (désigné aux présentes sous le nom de « vous » ou « votre ») de produits Zephyr (les « Produits ») que lesdits produits sont ex