S100 High Resolution Resin 3D Printer User’s Manual
Contents How this type of printer Works ............................................................................................................. 3 Safety Warnings And Guiding ............................................................................................................... 3 Package Contents ...................................................................................................................................... 4 Product Overview ...............................................
How this type of printer Works An LCD based resin printer uses an LCD screen to mask the shape of a layer of your model one layer at a time while using UV lights to cure the resin. Between layers, the printer will lift the print and return it one layer higher than previously. This process is repeated layer by layer to shape the object over time. Safety Warnings And Guiding • This 3D Printer includes moving parts that can cause injury.
Package Contents 1 x 3D Printer 1 x Memory Card 1 x Hex Wrench 1 x Sample Resin 1 x Power Adapter 1 x AC Power Cord Product Overview 1. Acrylic cover 2. Leveling Knob 3. Printing Platform 4. Resin Tank 5. LCD display 6.
Connect Connect the power supply to this position and power on the machine. Auto Calibration The printer will automatically calibrate the build platform when homing and starting a print. It will calibrate the platform automatically. This function requires the vat to be free of cured resin particles. Please see the troubleshooting section for more detail. Using The Menu enu System •Pressing the top button will change the menu choice left and up.
User Interface Main Menu 1. Print from SD card. 2. Manage profile file 3. Manual control page. Control Interface 1. Control the movement of Z axis. 2. Back to the home position. 3. Turn on the UV lamp for 10 seconds. This can be used to clean the resin vat by curing an entire layer and peeling that layer from the FEP liner. 4. Back to the Main menu. Printing Interface 1.
2. Printing status 3. Printed layers/Total layers progress 4. Adjust the cure time of the base three layers 5. Adjust the cure time for layers other than the first three base layers 6. Adjust the raise distance 7. Pause the printing 8. Printed height/Total height progress 9. Cancel the print Finish Screen 1. Print the same model again 2. Back to the main menu WIFI Setup 1. The below screen will be shown upon powering on your printer. 2. Enter the provided URL into your computer’s browser: http://bit.
3. Copy the generated file onto the SD card that came with your printer. Turn off the printer, insert the SD card, and turn the power back on. Upon turning the printer back on, the file will be detected on the SD card and will configure your printer to connect to the SSID and Password provided in step 2. Please note, this printer is designed to use a 2.4 GHz network band. Additionally, please ensure that the printer is placed in a location with a strong Wi-Fi network signal.
WEB UI 1. The status of your Wi-Fi Fi connection can be seen on the home screen in the top left hand corner. Once the printer is connected to the Wi-Fi network, it will display the IP address. To access the Web UI, please enter the IP address into the browser on a computer connected to the same me network. 2. To prevent others from potentially tampering or controlling your printer remotely, there is security verification on the first access of the Web UI.
(2).Printer Management (3).Upload print file (4).Select the file and click the "Print" button to start printing. (5).Profile management (a).Resin: Name of the profile file (b).Burn in second: the cure time of the base three layers (c).Exposure second: the cure time for layers other than the first three base layers (d).Separation: the raise distance (6).WEB Slicer 4.
Troubleshooting 1) If the print finishes and there is nothing on the build plate there are 3 potential reasons: a) The first layers did not cure enough and the print has fallen off of the build plate. Increase the base cure time. For Malyan resin, 60 seconds for the base cure time will work. Other resins may require different amounts of curing time. b) The platform did not level correctly.
IV) This moment can be used to clean the resin vat, but it is not necessary. Remove any remaining pieces of cured resin from the vat, and reinstall it onto the printer. When printing the first few layers, you can click the "Pause" button to raise the print platform, so that it will be easy to observe whether the first layer adherence to the platform.
About Resins Resin storage Resins should be kept in the dark and ventilated place, storage temperature: 20°C-30°C, lower temperature can extend the shelf life, the official resin shelf life is one year. Resin operation When operating, please wear gloves and avoid direct contact as possible. Cured resin is safe to be handled without gloves. If exposed to skin, wash the exposed location promptly. Printed models should not be used for food applications.
useful to cure unwanted resin prior to throwing it away. Tips 1. Check the resin box and platform before printing ensure they are clean. 2. After taking out the model, remember to cover the lid to prevent the resin curing. 3. After finish printing, you can keep the resin in other container or in the resin box. After using, the storage period of resin will be correspondingly shorter, and need to run out as soon as possible, add fresh resin can effectively improve the shelf life of the resin. 4.
Creation Workshop Tutorial Here we introduce the settings and slicing steps. Run the "Creation Workshop" program in the "Creation Workshop" folder.
After importing the model, you can add support as needed. Click the to open the support option, click where you need to add the support,then the support can automatically generate. The other two buttons are (bottom support) and (automatic support). The thickness of support can be adjusted, the top must not be less than 0.25MM, the root not less than 0.6MM. If you model by using PRO/E and CREO, FRONT face is the "bottom" of the model instead of TOP.
"Enable Slice Out lines" is the feather value option (set the value, the more the more smooth), feather rate can reduce the model pixel pattern. The general value of 3 or more, can effectively alleviate. "Slice Thickness (mm)" setting range: 0.02-0.1mm.the default is 0.05mm, the smaller the thickness is, the higher the accuracy will be, and more time the printing will need. Exposure time can be reduced if the layer thickness is smaller. “Exposure time (ms)”can be set according to the actual situation.
height of the Z-axis table. "Z-axis lift s peed (mm/m)" default setting: 100mm/m, the setting range is recommended between 50-150mm/m. "Z-axis retraction s peed (mm/m)" default setting: 100mm/m, the setting range is recommended between 100-150mm/m. Note: Remember to click the “Apply Changes” button to take effect after your setting is completed.
5. Copy the CWS file into the SD card or send the file over the network, then you can print the model you need. REGULATORY COMPLIANCE Notice for FCC This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
·Consult the dealer or an experienced radio/TV technician for help. Modifying the equipment without Malyan’s authorization may result in the equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
