V1.1.2 20210721 Aries 3D Printer User Manual WARNING Each printer must be tested before leaving factory. If there are some residues in extruder or some tiny scratches on the build plate, it is normal and won’t affect the printing quality.
Foreword Thank you for choosing and using the products of Voxelab Technology. For your convenience, please read this manual carefully before use and follow the manual strictly. The Voxelab team is always ready to provide you with the perfect service. Please contact us by email listed, if you have any problems. Email：support@voxelab3dp.com You can also get operational knowledge of the equipment from the following way: Voxelab website: www.voxelab3dp.
Unpacking 1. Open the box, take out the user manual, the USB flash disk and the platform. 2. Remove the foam. 3. Lift the printer and put it on the desk, then 4. Remove the top foam, there should be a take Aries out of the plastic bag. power cable included. 6. Hold the platform and lift it carefully to remove the foam below it. 5. Take out the foam under nozzle as showed in the image.
7. Double check the foam, it should contain: filament, material rack, nozzle, remove tool, needle, wrenches and screwdrivers. 8. Cut the three black cable ties: one for fixing X-axis synchronous belt, two for fixing Y-axis synchronous belts on both sides. 9. Cut four white cable ties that used to hold the rods in place. 10. Discard the blue protective tapes all around. 11. Congratulations! You’ve unpacked your printer. Please keep the kit and packing for future use.
Notes 1. Do not make any modifications to the printer. To avoid personal injury or property damage please ensure your operation followed by the Manual. 2. Dress properly. Do not wear loose clothing or jewelry. Keeping your hair, clothing and gloves away from moving parts. 3. Do not directly touch the nozzle and build plate to avoid high-temperature burn. 4.
Kit Contents V1.0 20210401 Aries 3D Printer User Manual WARNING Each device must be tested before leaving factory. If there are some residues in extruder or some tiny scratches on the build plate, it is normal and won’t affect the printing quality.
Equipment Parameters Model Voxelab Aries Print size 200*200*200 mm Forming technology FDM Number of nozzle 1 Layer thickness 0.05 mm - 0.4 mm Nozzle diameter Standard 0.4 mm XY axis precision ±0.2 mm Filament φ1.
Product Introduction 17 11 13 12 1 2 14 15 16 3 4 6 5 7 10 8 9 3. Z-axis Guide Rod 4. Build Plate 1. Y-axis Guide Rod 2. X-axis Guide Rod 5. Clip 6. Limit position assembly 7. Nut 9. USB Stick Input 10. Power Voltage Switch 11. LED Light 12. Nozzle 13. Turbofan Baffle 14. Power Switch 15. Power Input 16. Spool installation port 17. Drive assembly 07 8.
Hardware Assembly Glass Build Plate 1. Put the glass build plate on the heating platform and insert it into the limit position assembly, then locked by clips. The four edges of glass build plate need to be aligned with the platform. Locked Unlocked Rotate 180° to the inside Rotate 180° to the outside 2. Install the material rack on the back of printer.
3. Follow the filament loading direct strictly(as showed) and insert the filament into the intake. It needs to press the handle to push filament into filament feeding roller until certain resistance is sensed. Note：Please ensure the filament direct is the same as the picture showed, or it will cause the print failure. Power On Plug in the power cord and toggle the switch to turn on the power. Do not disconnect the cables when Aries is powered on. Attention · Damage might occur if voltage setting is incorrect.
Leveling Build Plate Before leveling, let's learn the function of nuts. How to use the nuts Build plate goes up Build plate goes down Rotate the nuts Anticlockwise Rotate the nuts clockwise Raise the build plate to reduce the distance between the nozzle and build plate. Lower the build plate to increase the distance between the nozzle and build plate. 1. Put a piece of A4 paper on the build plate, tap the touchscreen [Control] - [Level] and wait for the extruder moving to the first leveling point.
3. When the extruder move to the second point, pull the A4 paper to feel the friction resistance. If the friction is too big to move, rotate nut anticlockwise to increase the distance of nozzle and build plate; if the friction is too small, rotate nut clockwise to reduce the distance of nozzle and build plate. It is better that pulling the paper and feel the significant frictional resistance until the slight scratches appear without damage. Tap [Next] to do the third level point. 4.
Loading Filament 1. Tap [Control]. 2. Tap [Load]. 3. The extruder is heating to the targeted temperature automatically. 4. The auto-load is start to load the filament when 5. Tap [OK] to back to the homepage. the targeted temperature reached. Do not stop loading when the nozzle extrudes the filament. It is suggested that load the filament evenly then tap [OK].
First Print Suggestions 1. Ensure that the build plate has been leveled before printing. 2. Ensure that the filament has been loaded in an appropriate approach. 3. Please clean extruder before printing (Load the filament for a while to extrude all the melted filament you printed last time out of the extruder). 4. Do not leave the printer unattended during operation. Decompressed the slicing software package in the USB flash drive and install it to your computer.
Unloading Filament Please follow steps below if you need to unload filament in daily use. 1. Tap [Control]. 2. Tap [Unload]. 3. When the filament unload out of the filament feeding port, the unload operation is finished. Note: After unload completed then load again, it can finish the filament replacement.
WIFI Connection 1. Tap [Settings] - [WIFI], open the WIFI function. 2. Choose the Internet and save the password.
Connect Printer by WIFI 1. After the WIFI connected successfully, tap [Info] and check the IP Address. 2. Open the VoxelMaker, click [Print] - [Connect Machine], input the IP address and click the connect. 3. There is a connect icon when it connected successfully.
Firmware Upgrade Get the firmware files: Enter the official website and download them at . Method 1: 1. Copy the firmware into the blank USB flash disk. 2. Plug in the USB flash disk into the USB port of printer and reboot the printer, waiting for the upgrade process finished. 3. Plug out the USB flash disk after hearing three buzzes, reboot printer again. 4. After the upgrade completed, please delete the firmware file in the USB flash disk to avoid upgrading repeatedly next time.
Slicing Software 1 2 3 4 5 6 7 8 1. Load the STL file. 2. Enter the support setting mode. 3. Enter the slicing setting mode. 4. Observe the STL file in different views mode. 5. Move the STL file in the X or Y axis directly, it can be moved in Z -axis directly by long pressing shift and the mouse. 6. Rotate the STL file. 7. Scale the STL file. 8. Cut the STL file in different angles.
19 Power port Nozzle wire port X-axis sensor port Filament sensor port Z-axis motor port Y-axis sensor Platform temperature Reserved detection port port Y-axis X-axis motor port motor port Fuse Hotbed wire port Extrusion motor port PCB cooling fan port Z-axis sensor port Reserved port Screen port Debug port Wiring connection
Printing Notice 1. The adhesion of glass build plate may decrease after long time using. Please apply proper amount of glue to keep and improve the adhesion. 2. Warping issues may occur when print ABS filament in cold environment, you may use glue to enhance the adhesion. It's not recommended to print ABS filament at extremely low temperature environment, as print will fail when printed model getting away from the build plate. 3.
FAQ Q：How to get the firmwares? A：Enter the official website and download them at the . Q：What if the model warps or is unable to stick to the build plate? A：1. The temperature of the build plate was too low; please increase its temperature； 2. Filament failed to adhere or bond on the build plate, use glues to enhance the adhesion； 3.
Q：What if the files are garbled and cannot be read? A： 1. The format of files after slicing is not compatible; 2. Repair the model before slicing. Q：What if knock and noise occur when nozzle returning to zero point? A： 1. Check whether the zero sensor is knocked and broken; 2. Check the lines and see whether the noises stop when pressing the sensorby hand; 3. Contact us by email. Email: support@voxelab3dp.com Q： What if offset occurs on the finished model? A： 1.
Metal Scraper Allen Wrench Stamping Wrench Tools Bag Accessories Build Plat USB Stick USB Cable TF Card Card Reader independently due to upgrading. Glue Filament * Filament Spool Voxelab extruder kit shall be purchased Plastic Scraper Build Tape Parts Excluded from This Warranty · Unable to provide valid After-sales Service Card or serial No.
After-sales Service Registration Form Please fill in this form carefully, cut out this form and mail it back to Voxelab together with the printer, or download this form from www.voxelab3dp.com, fill in this form and mail it to aftersales@voxelab3dp.com. After-sales service shall not be provided without this form. Please contact your printer's reseller to get After-sales service help if your printer is not purchased on official Voxelab website.
Official Website Scan QR to Get More After-sales Support FCC Caution. (1)§ 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.
