6212-I2 4-Port Router User’s Guide November 2005 Document Part Number: 6212-A2-ZB23-10
Zhone Technologies @Zhone Way 7001 Oakport Street Oakland, CA 94621 USA 510.777.7000 www.zhone.com info@zhone.com COPYRIGHT 2000–2005 Zhone Technologies, Inc. All rights reserved. This publication is protected by copyright law. No part of this publication may be copied, distributed, displayed, modified, transmitted, stored in a retrieval system, or translated without express written permission from Zhone Technologies, Inc.
! Important Safety Instructions 1 Read and follow all warning notices and instructions marked on the product or included in the manual. 2 Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3 Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord.
CE Marking When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com. FCC Part 15 Declaration An FCC Declaration of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com. This device complies with Part 15 of the FCC Rules.
This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service Order Code (USOC) type RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It has been designed to be connected to a compatible modular jack that is also compliant.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
CONTENTS Document Summary ...................................................................................................11 Chapter 1 Introduction ............................................................................................................13 Features ........................................................................................................................13 System Requirements .................................................................................................
Chapter 4 Quick Setup ............................................................................................................35 Quick Setup with Auto-Connect Enabled ...............................................................35 Quick Setup with Auto-Connect Disabled ..............................................................36 Chapter 5 Advanced Setup ....................................................................................................41 WAN ....................................
Configure System Log ............................................................................................72 SNMP ...........................................................................................................................73 Internet Time ...............................................................................................................74 Access Control – Services .........................................................................................
6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
ABOUT THIS GUIDE This guide contains detailed information about the 6212-I2 router. It is intended for all users of the router. Document Summary 6212-A2-ZB23-10 Section Description Chapter 1, Introduction Describes the features of the router. Chapter 2, Hardware Installation and PC Setup Shows how to connect the router and set up your PC to manage the router. Chapter 3, Device Information Explains how to use the web interface to obtain statistics and other information about the router.
6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
INTRODUCTION Congratulations on becoming the owner of a 6212 ADSL router. This User’s Guide will show you how to set up the router, and how to customize its configuration to get the most out of this product. Features The 6212 router has the following features: z z z Built-in ADSL modem which offers G.dmt, G.lite, T1.413, ADSL2, Annex L, and ADSL2+ to meet different linking speeds from your ISP. Four 10/100BaseT Ethernet ports to provide Internet connectivity to all computers on your LAN.
Introduction Parts List In addition to this document, your 6212 ADSL router should come with the following: z 6212 ADSL router z Power adapter z Ethernet cable (RJ45, straight-through type) z Phone cable (RJ11) Front Panel The front panel contains LED indicators that show the status of the unit.
Rear Panel Table 1: Front Panel Label and LEDs (Sheet 2 of 2) Label Color Function LAN 1–4 Green On: The Ethernet interface is successfully connected to a device through the LAN port. Flashing: Data transfer at LAN connection Off: No LAN link ALARM Red On: ADSL is not connected. Off: ADSL is connected. POWER Green On: Unit is powered on. Off: Unit is powered off.
Introduction 16 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
HARDWARE INSTALLATION AND PC SETUP Overview This chapter provides basic instructions for connecting the router to a computer or a LAN and to the Internet using DSL. The first part provides instructions to set up the hardware, and the second part describes how to prepare your PC for use with the router. It is assumed that you have already subscribed to DSL service with your Internet service provider (ISP). Connecting the Hardware Shut down your PC and any other equipment before connecting it to the router.
Hardware Installation and PC Setup RESET LINE CONSOLE DEFAULT LAN 1 LAN 2 LAN 3 LAN 4 Power Switch POWER 05-17712 Figure 3: Hardware Installation 5 Turn on your PC and any other LAN devices, such as hubs or switches. 6 Turn on the router using its power switch. 7 Verify that the router's LEDs are illuminated as shown in Table 3. Table 3: 18 LED Indicators (Sheet 1 of 2) This LED . . . Should be: POWER Solid green to indicate that the device is turned on.
Configuring Your Computer Table 3: LED Indicators (Sheet 2 of 2) This LED . . . Should be: LAN 1–4 Solid green to indicate that the device can communicate with your PC via Ethernet, or flashing when the router is sending or receiving data over Ethernet. If the LEDs are illuminated as expected, the router is working properly. Configuring Your Computer Before you can access the router over the LAN you have to configure your PC's TCP/IP address to be 192.168.1.
Hardware Installation and PC Setup Figure 5: Windows Version Windows XP 1 In the Windows task bar, click on the Start button, and then click on Control Panel. 2 Double-click on the Network Connections icon. 3 In the LAN or High-Speed Internet window, right-click on the icon corresponding to your network interface card (NIC), and select Properties. (Often this icon is labeled Local Area Connection). The Local Area Connection dialog box displays with a list of currently installed network items.
Configuring Your Computer Figure 6: Network Connections (Windows XP) Figure 7: Local Area Connection Properties (Windows XP) 5 In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio button labeled Use the following IP address. Type an address between 192.168.1.3 and 192.168.1.254 in the IP Address field (192.168.1.20 is shown here as an example) and 255.255.255.0 in the Subnet Mask field.
Hardware Installation and PC Setup Figure 8: TCP/IP Properties (Windows XP) 6 Click on OK twice to confirm your changes, and close the Control Panel. Windows 2000 1 In the Windows task bar, click on the Start button, point to Settings, and then click on Control Panel. 2 Double-click on the Network and Dial-up Connections icon. 3 In the Network and Dial-up Connections window, right-click on the Local Area Connection icon, and then select Properties.
Configuring Your Computer 8 After restarting your PC, double-click on the Network and Dial-up Connections icon in the Control Panel. 9 In Network and Dial-up Connections window, right-click on the Local Area Connection icon, and then select Properties. 10 In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP), and then click on Properties. 11 In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio button labeled Use the following IP address.
Hardware Installation and PC Setup 192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask field. 13 Click on OK twice to confirm and save your changes, and then close the Control Panel. Windows 95 and Windows 98 1 In the Windows task bar, click on the Start button, point to Settings, and then click on Control Panel. 2 Double-click on the Network icon. The Network dialog box displays a list of currently installed network components.
Logging in to Your Router 3 In the Network dialog box, click on the Protocols tab. The Protocols tab displays a list of currently installed network protocols. If the list includes TCP/IP, the protocol has already been enabled. Skip to Step 9. 4 If TCP/IP does not appear as an installed component, click on Add. 5 In the Select Network Protocol dialog box, select TCP/IP, and then click on OK. You may be prompted to install files from your Windows NT installation CD or other medium.
Hardware Installation and PC Setup Figure 9: Login Screen If you have problem connecting to the router, verify that your PC is properly configured within the subnet of the router's default IP address 192.168.1.1. Setup is described in Configuring Your Computer on page 19. 2 Enter your user name and password, and then click on OK to display the home page of the router's web interface.
Logging in to Your Router Figure 10: Web Interface Home Page 6212-A2-ZB23-10 6212-I2 4-Port Router User’s Guide 27
Hardware Installation and PC Setup 28 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
DEVICE INFORMATION Status Summary Display the general status report for the router by clicking on Summary under Device Info (Figure 11). Figure 11: Status Summary WAN Display the WAN status report from the by clicking on WAN under Device Info (Figure 12).
Device Information When a WAN connection is configured, the screen looks like Figure 13. Figure 13: WAN Status with WAN Connection LAN Statistics Display LAN statistics by clicking on LAN under Statistics (Figure 14). Figure 14: LAN Statistics WAN Statistics Display WAN statistics by clicking on WAN under Statistics (Figure 15).
ATM Statistics Figure 15: WAN Statistics ATM Statistics Display ATM statistics by clicking on ATM under Statistics (Figure 16). Figure 16: ATM Statistics ADSL Statistics Display ADSL statistics by clicking on ADSL under Statistics (Figure 17).
Device Information Figure 17: ADSL Status ADSL BER Test The ADSL Bit Error Rate (BER) test determines the quality of the ADSL connection. The test is performed by transferring idle cells containing a known pattern and comparing the received data with this known pattern to check for any errors (Figure 18 and Figure 19). To run a BER test: 1 Click on the ADSL BER Test button. 2 Select the test duration and click on Start 3 Check the result.
Route Figure 18: ADSL BER Test — Start Figure 19: ADSL BER Test — Result Route Obtain the Routing status report by clicking on the Route item under Device Info (Figure 20) 6212-A2-ZB23-10 6212-I2 4-Port Router User’s Guide 33
Device Information Figure 20: Route Information ARP Display the ARP status report by clicking on ARP under Device Info (Figure 21) Figure 21: ARP Status 34 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
QUICK SETUP Quick Setup with Auto-Connect Enabled Auto-connect will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To use auto-connect: 1 Select Quick Setup. The Quick Setup initial screen appears. Figure 22: Quick Setup Initial Screen 2 Select DSL Auto-Connect, then click on Next. The progress information screen appears.
Quick Setup Figure 23: Detecting Available PVC Figure 24: Detecting available PVC – Available PVC Detected Quick Setup with Auto-Connect Disabled 1 Select Quick Setup. The Quick Setup initial screen appears. 2 Verify that DSL Auto-Connect is not selected. Entry boxes for VPI and VCI appear when DSL Auto-Connect is not selected. 3 Specify VPI and VCI as directed by your ISP.
Quick Setup with Auto-Connect Disabled Figure 25: Specifying VPI and VCI 4 Click on Next. The Connection Type screen appears. Figure 26: Connection Type 5 Select the protocol and encapsulation type required by your ISP. 6 Click on Next. Further parameters for the selected protocol are presented. For example, if you selected PPPoA, the PPP Username and Password screen appears.
Quick Setup Figure 27: PPP Username and Password 7 Click on Next. The Network Address Translation Settings screen appears. Figure 28: NAT Settings 8 Enter the settings specified by your ISP and click on Next. The Device Setup screen appears.
Quick Setup with Auto-Connect Disabled Figure 29: Device Setup 9 If desired, configure configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond to your LAN's IP Subnet. If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers. Disable the DHCP server if you would like to manually assign IP addresses.
Quick Setup Figure 30: WAN Setup - Summary 40 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
ADVANCED SETUP WAN Set up WAN parameters as directed by your ISP. Figure 31: WAN Setup Screen Add Function – ATM PVC Configuration If you want to add a new rule for the WAN interface, click on the Add button. The ATM PVC Configuration screen appears. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category.
Advanced Setup Figure 32: ATM PVC Configuration Screen Verify the following values with your ISP before you change them. z VPI (Virtual Path Identifier) – The valid range is 0 to 255. z VCI (Virtual Channel Identifier) – The valid range is 32 to 65535.
WAN Connection Type Screen 1 Select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use, then click on Next button. Figure 33: Connection Type Screen 2 Select a connection type and click on Next. In this example, the Bridge Service screen appears. Figure 34: Bridge Service Screen 3 Enter or select the parameters presented for the service type, and click on Next. The WAN Setup - Summary screen appears.
Advanced Setup WAN Setup - Summary 1 Make sure that the settings on the WAN Setup - Summary screen match the settings provided by your ISP. If all settings are correct, click on the Save button to save these settings; if not, click on the Back button to make any modifications. If you want to change any item after saving, click on the Edit button to make any modifications.
Local Area Network (LAN) Setup Finish Function After you change any item in WAN Setup, remember to click on the Finish button to apply the changes and reboot the system. Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to conform your LAN's IP Subnet. If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers.
Advanced Setup Figure 38: NAT Virtual Server Setup You can select a Service or make new one. Enter the Server IP Address, then click on Save/Apply to submit your configuration. Figure 39: Virtual Server Add Screen On this screen you can view and delete servers. Click in the check box under Remove and click on the Remove button to delete selected virtual servers.
Port Triggering Figure 40: Removing Selected Virtual Servers Port Triggering Click the on the Add button to add Port Triggering for your Internet application. Figure 41: Port Triggering Setup Page You can select an application every time or create new one for your application. Then click on Save/Apply to save your settings.
Advanced Setup Figure 42: Port Triggering Add Page On this screen you can view and delete applications. Click in the check box under Remove and click on the Remove button to delete selected applications. Figure 43: Port Triggering List DMZ Host You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save/Apply.
Firewall Figure 44: DMZ Host Setup Firewall For security reasons, firewall options can be configured only from the LAN side of the router. IP Filtering – Outgoing The outgoing filter will block the traffic from the LAN side to the WAN side. Click on Add to create filters. Figure 45: IP Filtering – Outgoing Filter Setup Input the filter name, source information (from the LAN side), and Destination information (from the WAN side). Then click on Save/Apply.
Advanced Setup Figure 46: IP Filtering - Outgoing Filter Add Page You can view and delete the outgoing filter settings on this screen. Figure 47: IP Filtering - Outgoing Filter Setup List IP Filtering – Incoming Incoming filter filters the traffic from the WAN side to the LAN side. Click on Add to add incoming filter settings.
Firewall Figure 48: IP Filtering – Incoming Filter Setup Page Enter a filter name, information about the source address (from the WAN side), and information about the destination address ( to the LAN side). Select the protocol and WAN interface. Then click on Save/Apply to add the setting. Figure 49: IP Filtering - Incoming Filter Add You can view and delete the incoming filter settings from this screen.
Advanced Setup Figure 50: IP Filtering - Incoming Filtering List Firewall – MAC Filtering MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. Figure 51: IP Filtering - MAC Filtering Setup If you click on Change Policy, a confirmation dialog lets you verify your change.
Firewall If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save/Apply to save it. Figure 53: IP Filtering - MAC Filtering Add Page On this screen you can view and delete MAC filtering rules. Figure 54: IP Filtering - MAC Filtering List Parental Control Use the Parental Control feature to restrict the days and times a particular device is allowed to access the Internet.
Advanced Setup Figure 55: Parental Control Screen To set up parental controls: 1 Click on Add. The Time of Day Restriction screen appears. Figure 56: Parental Control – Time of Day Restrictions 2 Enter a User Name to identify the target of the restrictions. 3 Enter the MAC address of the network adapter to be restricted, and, optionally, another MAC address. 4 Select the days of the week the restriction is in force. 5 Specify the start and end times the restriction is in force.
Port Mapping Port Mapping Use the Port Mapping screen to map multiple ports to a PVC and create bridging groups. Each group will perform as an independent network. Figure 57: Port Mapping To create a new mapping group: 1 Click on Add. The Port Mapping Configuration screen appears. Figure 58: Creating a Port Mapping Entry 2 Enter a unique Group name.
Advanced Setup Quality of Service You can configure the Quality of Service to apply different priorities to traffic on the router. Figure 59: Quality of Service Setup Click on Add and the Add Network Traffic Class Rule screen appears. To add a rule: 1 Give a name to this traffic class. 2 Assign a priority level-low, medium, and high-to this traffic class. 3 Select an IP precedence from the range of 0–7.
Routing – Default Gateway Figure 60: Quality of Service Add Screen Routing – Default Gateway You can change the Default Gateway on the Routing - Default Gateway screen. By default the Enable Automatic Assigned Default Gateway box is checked.
Advanced Setup If you want to specify the default gateway address, then uncheck the box as seen below. Enter the default gateway address and, optionally, the WAN interface you will use. Click on Save / Apply to save the settings. If you add or change the default gateway address, you must reboot the router to put the new default gateway IP address into effect. Figure 62: Default Gateway Setup Routing – Static Route Use the Routing - Static Route screen to add a static route to the routing table.
Routing – RIP Figure 64: Static Route Add Routing – RIP If RIP is enabled, the router operation can be configured as Active or Passive. Figure 65: RIP Setup DNS Server Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and secondary DNS.
Advanced Setup Figure 66: DNS Setup Dynamic DNS Use the Dynamic DNS screen to alias a dynamic IP address to a static hostname, allowing your router to be easily accessed from anywhere on the Internet.
ADSL To set up a Dynamic DNS entry: 1 Click on Add. The Add Dynamic DNS screen appears. Figure 68: Adding a Dynamic DNS Entry 2 Select a D-DNS Provider from the drop-down list. 3 Enter the Hostname you have selected for the interface. 4 Select the router Interface from the drop-down list. 5 Enter the information you used to register with the dynamic DNS service: for DynDNS, enter your Username and Password; for TOZ, enter your E-mail address and Key. 6 Click on Save/Apply.
Advanced Setup Modulation Methods The following modulation methods are supported by the 6212 ADSL router: z G.dmt Enabled z G.lite Enabled z T1.413 Enabled z ADSL Enabled z Annex L Enabled z ADSL2+ Enabled. Do not change this setting unless so directed by your ISP. Phone Line Pair The 6212 ADSL router supports phone lines on pins 2 and 3 or pins 1 and 4 to connect your ADSL line.
Tone Selection z z No Retrain: In this mode the router will try to establish a connection as in normal mode, but once the connection is up it will not retrain if the signal is lost. L3: Puts the router into the L3 power state. Select a test mode and click on Apply. Then click on Tone Selection. Figure 70: DSL Advanced Settings Tone Selection To view the ADSL Tone Settings screen, click on the Tone Selection button of the DSL Advanced Settings screen (see Figure 70).
Advanced Setup Figure 71: Tone Settings 64 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
DIAGNOSTICS Testing the DSL Connection The diagnostics screen allows you to run diagnostic tests to check your DSL connection. The screen shows test results for three connections: z Connection to your local network z Connection to your DSL service provider z Connection to your Internet service provider Use the Test and Test with OAM F4 buttons to retest if necessary.
Diagnostics 66 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
MANAGEMENT Saving and Restoring the Configuration The configuration of your router can be backed up to a file, and also can be restored from a file. You can also restore the router to its factory default configuration. Backing Up Configuration Settings To back up your settings, select Management -> Settings -> Backup Settings. Figure 73: Back Up Settings Screen Verify that you would like to save the file.
Management Figure 74: Backup Settings Upload Confirmation Select the location where you want to save the file.
Restoring Configuration Settings Restoring Configuration Settings To restore saved settings, select Management -> Settings -> Restore User Settings. Figure 76: Restore User Settings Screen Select the backup file you want to restore and click on Update Settings. Figure 77: Restore Settings File Location The router will restore settings and reboot to activate the restored settings.
Management Figure 78: Upload in Progress Screen Restoring Default Settings Restore Default will erase all current settings and restore the router to factory default settings. To restore the router to factory default settings, select Management -> Settings -> Restore Default. Figure 79: Restore Default Settings Screen Reply OK to the confirmation dialog.
System Log Figure 80: Restore Default Confirmation Dialog The router will restore the default settings and reboot. Figure 81: Restore Default Settings Reboot System Log The System Log dialog allows you to view the System Log and configure the System Log options.
Management View System Log Click on the "View System Log" button to check the log file. Figure 83: View System Log Configure System Log If the log is enabled, the system will log selected events: Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. All events above or equal to the selected log levels will be logged (maintained in the system log file) and displayed.
SNMP Figure 84: System Log Configuration Select the desired values and click on the "Save/Apply" button to configure the system log options. SNMP Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in the router. Use the SNMP screen to set up parameters for SNMP access. Figure 85: SNMP Screen Select the desired values and click on Save/Apply to configure the SNMP options.
Management Internet Time Use the Internet Time screen to specify whether the router uses Simple Network Time Protocol (SNTP) to obtain the time of day from NTP servers on the Internet. To set up the router to obtain time from an NTP server: 1 Select “Automatically synchronize with Internet time servers”. The SNTP fields appear. Figure 86: Internet Time Screen 2 Select NTP servers. 3 Specify the time zone offset for your router’s location. 4 Click on Save/Apply.
Access Control – Services Access Control – Services You can enable or disable some services of your router by LAN or WAN. If no WAN connection is defined, only the LAN side can be configured. Figure 87: Services Setup Access Control – IP Addresses Web access to the router can be limited when Access Control Mode is enabled. The IP addresses of allowed hosts can be added using Access Control -> IP Address.
Management To assign the IP address of the management station that is permitted to access the local management services, enter the IP address in the box and click on the Save/Apply button. Figure 89: Access Control – IP Address Add Screen Access Control – Passwords Use Access Control -> Passwords to change a password. Select an account and enter the current password and the new password. Then click on Save/ Apply.
Update Software Update Software If your ISP releases new software for this router, follow these steps to perform an upgrade. 1. Obtain an updated software image file from your ISP. 2. Enter the path to the image file location or click on the "Browse" button to locate the image file. 3. Click on the Update Software button once to upload the new image file. Figure 91: Update Software Note The update process takes about two minutes to complete, and your router will reboot automatically.
Management 78 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
SPECIFICATIONS Specifications are subject to change without notice. Table 5: 6212-I2 Specifications 6212-A2-ZB23-10 Specification Criteria Environment Operating Temperature: 32° F to 104° F (0° C to 40° C) Storage Temperature: –4° F to 149° F (–20° C to 65° C) Humidity: 5% to 95%, non-condensing Interfaces DSL Line: RJ11 Ethernet: 10/100BaseT, RJ45 Power 100 VAC, 50 Hz 110 VAC, 60 Hz 220 VAC, 50/60 Hz Protocol Support ANSI T1.413 (Full Rate ADSL) ITU G.992.1 (DMT) ITU G.992.2 (G.lite) ITU G.992.
Specifications 80 6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
INDEX A About This Guide 11 Access Control IP Addresses 75 Passwords 76 Services 75 ADSL 61 BER Test 32 Statistics 31 Advanced Settings, DSL 62 Advanced Setup 41 ARP 34 ATM PVC Configuration 41 Statistics 31 B DMZ Host 48 DNS 59 Dynamic 60 Document Purpose and Intended Audience 11 Summary 11 Domain Name Server 59 Dynamic DNS 60 E EMI Notice Canada 6 Japan 6 Environment 79 Ethernet cable 17 F Backing Up Configuration Settings 67 BER Test 32 Bridge Service 44 Bridging groups 55 C Cables Installing 17 Ca
Japan Notices 6 Default 26 PC Setup 17 Phone Line Pair 62 Port Mapping 55 Port Triggering 47 Power Specifications 79 Supply 17 Protocols Supported 79 PVC Adding 41 Configuring 41 Detecting 35 L Q LAN ports, connecting 17 Local Area Network (LAN) Setup 45 Statistics 30 Logging In 29 Quality of Service 44, 56 Quick Setup 35 Restricting access 53 Internet Time 74 Introduction 13 IP Address Access Control 75 Of Router 19 IP Filtering Incoming 50 Outgoing 49 J M MAC Filtering 52 Management 67 Mapping por
Status ARP 34 Route 33 Summary 29 WAN 29 System Log 71 Configuring 72 System Requirements 13 T Test BER 32 DSL Connection 65 Time 74 Tone Selection 63 U Update Software 77 User Name, Default 26 6212-A2-ZB23-10 V View System Log 72 Virtual Servers 45 W WAN 29, 41 Setup 44 Statistics 30 Status 29 Web Interface Home Page 27 Using 29 Weight 79 Windows 2000 22 Windows 95 24 Windows 98 24 Windows ME 23 Windows NT 24 Windows XP 20 6212-I2 4-Port Router User’s Guide 83
6212-I2 4-Port Router User’s Guide 6212-A2-ZB23-10
