Table of Contents TABLE OF CONTENTS ............................................................................................................ 1 1. IMPORTANT INFORMATION............................................................................................. 2 SAFETY PRECAUTIONS ........................................................................................................... 2 2. INTRODUCTION ....................................................................................................
1. Important Information Please take the time to read this user manual before using the ZWD‐2422T and ZWD‐2422R. It contains important information about operating your Full HD video wireless kit. z z ZINWELL’s limited warranty applies when the product is handled properly for intended use, in accordance with its operating instruction.
EN 301 489‐17 Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro magnetic Compatibility(EMC) standard for radio equipment; Part 17: Specific conditions for 2,4 GHz wideband transmission systems, 5GHz high performance RLAN equipment and 5,8 GHz Broadband Transmitting Systems EN 60065 Audio,video and similar electronic apparatus—Safety requirements DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules.
z z z z z z z z z z CAUTION of RF module Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co‐located or operating in conjunction with any other antenna or transmitter.
z z z z z z co‐located or operating in conjunction with any other antenna or transmitter. End‐users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Outdoor operations in the 5150~5250MHz, 5600~5650MHz band are prohibited. This device has no Ad‐hoc capability for 5250~5350MHz and 5470~5725MHz. Outdoor operations in the 5470~5725MHz band are prohibited. This device could not be used in the 5600~5650MHz.
2. Introduction ZWD‐2422T and ZWD‐2422R wireless HD audio/video transmission solution allows users to place their HDTV set or projector where you want, free of the constraint of cables.
2.2 Overview A. ZWD‐2422T: Full HD Transmitter Main Unit Back Panel X IR Blaster Extender Jack Plug the IR Blaster Extender Cable into the IR OUT jack at rear panel of the transmitter. Attach the IR blaster to the device connected to the ZWD‐2422T. You can point your AV equipment’s existing remote control at the ZWD‐2422R receiver (usually close to your TV) to control connected device.
B. ZWD‐2422R: Full HD Receiver Main Unit Back Panel X IR Sensor Extender Jack Plug the IR Sensor Extender cable into the IR IN jack at the rear panel of the receiver. Generally, sensors with cable are placed near your HDTV set so that you can easily operate and control your AV equipment connected to ZWD‐2422T by pointing the remote control to the TV instead of the AV equipment. Front Panel Buttons and LEDs Y HDMI OUT For connecting the HDTV set via an HDMI cable.
C. Remote Controller Unit (RCU) Instruction Button POWER INFO. SOURCE CHANNEL WIDE Function Description Press to turn the ZWD‐2422 Transmitter/Receiver on/off. Press to display between “Channel”, “Source” and “ Signal Quality” Press this button to switch between audio/video sources connected to the ZWD‐2422T. Press this button to change between wireless channels manually if the user experiences video noise. Press this button to boost video transmission distance wirelessly.
D. On Screen Display (OSD) vs. RCU Instruction X Press the POWER button on the RCU or on Z Press the SOURCE button on the RCU or on the top of transmitter and receiver to enter the top of transmitter (or receiver) for “power saving mode” from “active mode”.
3. Installation Step1: Connect Two High‐Definition Audio/Video Sources and an HDTV to the ZWD‐2422T: (1) Connect the ZWD‐2422T’s (transmitter)“HDMI IN” to the High‐Definition AV sources’ “HDMI OUT” with an HDMI cable (included). The ZWD‐2422T has two HDMI inputs for the latest High‐Definition device, like PS3, Blu‐ray Player. (2) Connect the ZWD‐2422T’s (transmitter) “HDMI OUT” to the HDTV set’s “HDMI IN” port with an HDMI cable for the loop‐through output.
Step2: HDTV set Connection with ZWD‐2422R: (1) Connect the HDMI cable to the HDMI OUT jack of the ZWD‐2422R and to your HDTV set (or an HD projector). Press the Source / Input button of your TV’s remote to select the appropriate “HDMI” video input. (2) Connect the supplied power adapter to the DC IN jack of the ZWD‐2422R and a wall socket. The LED indicator in the POWER button lights up in solid blue when the ZWD‐2422T is connected to the power mains.
Step3: If necessary, connect the Infrared (IR) blaster (or sensor) Extender cable. Users can point hand‐held remote control of your High Definition AV equipment at the ZWD‐2422R or the HDTV set to operate the source devices, not exceeding the distance of 100 feet at Line‐of‐sight. (1) Plug the IR blaster cable into the IR OUT jack of the ZWD‐2422T. Place the IR blaster head near the IR sensor of your High‐Definition audio/video devices nearby.
Step 4: Power On Your ZWD‐2422T and ZWD‐2422R (1) Place the two AAA batteries into the remote control. (2) After the power cord is plugged into the electrical outlet, the ZWD‐2422 will be turned on automatically. (3) If it is in Standby mode (The POWER LED is lit in red), press the POWER button to turn on the ZWD‐2422T and ZWD‐2422R. It will take over 1 minute for the system to boot up. The ZWD‐2422R (receiver) cannot wake up the ZWD‐2422T (transmitter) wirelessly.
(4) If it is in Quick Start mode (The POWER LED is lit in purple), press the POWER button to turn on the ZWD‐2422T or ZWD‐2422R. It will take 20seconds for the system to boot up. The ZWD‐2422R (receiver) can wake up the ZWD‐2422T (transmitter) by wireless transmission. The transmitter can also wake up the receiver. Note : Please DO NOT press Power button on ZWD‐2422T and ZWD‐2422R in the same time to wake up; It’ll cause the wireless connection failed.
(6) Press the Source button, until you see the video being broadcasted from your device. (7) If you have electronic devices such as a cordless phone, wireless access point/ router sharing the 5GHz channel frequency, when you use it near the ZWD‐2422, you may experience disturbed picture or diminished sound quality. Press the CHANNEL button on the remote control to change the ZWD‐2422 to different channels. Note: A. Changing the ZWD‐2422 to a different wireless channel: 2.
B.
5745 5765 5785 5805 5825 Note : A. B. C. V V V V V 5 6 7 8 9 X X X X X X X X X X X X X X X X X X X X Gray background are indicates the DFS region. * means “Limited to indoor use”. NOT to use Weather Satellite Channels on DFS : i. 40MHz : Center Frequency 5590MHz, 5630MHz ii. 20MHz : Center Frequency 5600MHz, 5620MHz, 5640MHz (8) If all operation is normal, the POWER LED and SOURCE LED will glow in solid blue. Please refer to the next form containing detailed LED description : Note: A.
During system boot up, it required 1min or more for DFS channels scan and CAC waiting. Searching available channels Booting and Linking RF linking Searching available channels Booting and Linking Verifying signal. Verifying No input detected from selected source.
Step 5: For multi‐room audio/video transmission or transmission between different floors, user could press the “WIDE” button on the remote control to enable the Wide mode for longer‐range audio/video transmission.. Note : Only 1080i HD video transmission is available when enabling the “Wide” mode (OSD shows : WIDE Mode ON). Please shorten the distance and disable the “Wide” mode (OSD shows : WIDE Mode OFF) if full HD 1080p 60Hz content transmission is desired.
Step 6: Mounting the ZWD‐2422 to the Wall (5) Place ZWD‐2422 key holes over the protruding screws and slide down into position. (1) Refer the drawing of the bottom page that have relative position of the receiver key holes and attach this paper on wall. (2) Drill pilot holes. (3) Insert the supplied two Anchors into the wall. (4) Insert two screws into the anchors. Leave 1/8” length for mounting the receiver.
4. Troubleshooting Problem The ZWD‐2422 front panel power indicator (red LED) doesn't light up. Solution • Check if the power plugs of ZWD‐2422T/ZWD‐2422R are properly inserted into a functioning power outlet. • Verify that the proper cables have been selected and installed between the ZWD‐2422T (transmitter) input and your High‐Definition device output. • On your TV side (connected to the ZWD‐2422R), select the HDMI as input source. There is no video displayed on your TV screen.
5. Supported Resolution If the SOURCE LED continues to blink in blue (slower than “no signal” mode); OSD display: “Not a Supported Frame rate ” and there is no video displayed or the video quality suffers, it indicates that the video frame rate from your A/V source device is not supported. Ensure that the consumer timing of your HD device is compliant with the standard listed below: Video Format Timings Resolution Primary CEA Video Timing Primary CEA Video Timing 720(1440)x480i @ 59.
6. Audio Bit Rate Support Digital Audio from HDMI inputs: Up to 6Mbit/s bit‐rate support. Support AC3 and DTS. 2‐channel PCM over S/PDIF : 16~24 bits audio sample with 32~48KHz sampling rate 2channel PCM 32KHz 44.1KHz 48KHz 96KHz 16 bits YES YES YES n/a 24 bits YES YES YES n/a 2 to 8‐channel over S/PDIF : 16~24 bits audio sample with 32~96KHz sampling rate, over wireless high‐definition interface transmission.
7.
26
27