Instruction Manual

ManualsBrandsZippy ManualsAccessories for electricalDR1M-6221F

1.1 INTRODUCTION

First of all, thank you for purchasing DR1M series redundant power supply for 1U.

The DR1M is a 1+1 hot-swappable / hot-pluggable redundant power supply. It

consists of,

1) complete metal frame

2) compact size power module

3) backplane

The DR1M series redundant power supply offer a maximum 220 watts of output power.

The power module is in compact size, and built-in a 40mm ball bearing DC fan for

better ventilation. Each power module is designed with 6 outputs (+3.3V, +5V, +12V,

-5V, -12V, and +5Vsb) circuits, and compliant to ATX12V. All you can see on the

backplane is just passive components and this is the key point for longer MTBF.

The DR1M series offer a warning sub-system, including LED display, buzzer alarm,

TTL signal, It guides user the fast way to find out the power supply and DC fan status.

When all the power modules operate normally, it balances the load share through its

parallel design, which increases the reliability of power system.

To really discover the power system and ease in using it, we recommend you to read

through this manual carefully.

Summary of content (8 pages)

PAGE 1
.1 INTRODUCTION First of all, thank you for purchasing DR1M series redundant power supply for 1U. The DR1M is a 1+1 hot-swappable / hot-pluggable redundant power supply. It consists of, 1) complete metal frame 2) compact size power module 3) backplane The DR1M series redundant power supply offer a maximum 220 watts of output power. The power module is in compact size, and built-in a 40mm ball bearing DC fan for better ventilation. Each power module is designed with 6 outputs (+3.
PAGE 2
1.2 PACKING Your DR1M series should consist of the following, a) DR1M x 1 b) Accessory pack x 1 c) Product Manual x 1 1.3 MODEL DESINGATION Model number identification DR1M-6zzzy R 1 6 zzz y ----------- redundant in 1U height 6 output channel (+3.3V, +5V, +12V, -5V, -12V & +5Vsb) total output power, zzz –220 (unit: watts) F: built-in EMI FCC 1.
PAGE 3
PAGE 4
1.6 SPECIFICATION INPUT CHARACTERISTICS: DR1M-6220F l VOLTAGE: DC -36 V~ -72 V INPUT CURRENT: 7.0 A ( RMS ) FOR -48VDC l INRUSH CURRENT: LESS THAN 10A FOR EACH MODULE l OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT REGULATION OUTPUT MIN. [A] MAX. [A] LOAD LINE RIPPLE & NOISE 5V 3.0 25 ± 5% ± 50mV 50mV 12V 2.0 16 ± 5% ±50mV 120mV -5V 0 0.5 ±10% ± 50mV 150mV -12V 0 0.5 ±10% ± 50mV 150mV 3.3V 1.0 15 ± 5% ± 50mV 50mV +5VSB 0.1 2.0 ± 5% ± 50mV 50mV MAX.
PAGE 5
1.7 INSTALLATION & TESTING Mount the power supply into the system chassis by using proper mounting tool. The mounting holes of the power supply should match up with those in the chassis. Connect the power connectors to the M/B by following the M/B instruction. There is various on connectors / pinouts in both power supply and M/B. Please ensure to connect the matched one; otherwise, it will cause unexpected harms. Connect the remaining power connectors to the various peripherals as needed.
PAGE 6
1.8 Hot-swap procedures Please refer to the following when either power module is defective. 1) Locate the defective power module by examining the individual LED (if LED is distinguished, it indicates the power module is defective). *** WARNING: Please perform the following step carefully; otherwise, it may cause the whole system shutdown. *** WARNING: Please do not remove the defective power module until you have worn gloves to keep from been burned.
PAGE 7
1.9 PINOUTS AND FUNCTION OF THE CONNECTORS THE LED CONNECTOR OF TOTAL POWER SYSTEM PIN# 1 COLOR RED 2 BLACK 3 GREEN THE BUZZER RESET SWITCH CONNECTOR PIN# COLOR 1 2 BLACK YELLOW THE SIGNAL CONNECTOR OF POWER RESET PIN# COLOR COLOR 1 RED TTL SIGNAL 2 BLACK GND TTL signal: Sink current max. 5mA Source current max. 50uA Low Active ---Defective High ---Normal 1.10 TROUBLE SHOOTING If you have followed these instructions correctly, it should function normally.
PAGE 8
3) Once you hear the buzzer sound or see the warning LED in RED, please check, a) If the loading is under the minimum or over the maximum load of each channel. b) If the power source is well connected and supplied. Shall the above condition is happened, please disconnect the power source and wait for 2-3 minutes to release the protection status; then test it again. c) If buzzer keeps alarming or LED indicates the power module failure, please locate which power module is defective.