Instruction Manual

ManualsBrandsZippy ManualsAccessories for electricalM1Z3-6800P3V

1.1 INTRODUCTION

First of all, thank you for purchasing MyZx series redundant power supply.

The MyZx series is a N+1 hot-swappable / hot-pluggable redundant power supply. It

consists of,

The total output is up to your power’s requirements, you can figure out the total

Power’s consumption and check over the specification, the you can find out the

correct configuration.

It delivers full safety redundant (hot-swappable) function and provides the

hot-pluggable feature. In other words, it can offer a more reliable and safer, easy

install / maintain operation in the power energy supply to your system.

Its major function is to deliver the full power and the mean time these power modules

can mutually backup once one of the power modules is defective.

It provides a warning subsystem, include LED display, buzzer alarm, TTL signal etc.,

at the same time, it also indicates the status of the power system.

When all the power modules are at normal condition, it balances the load share and

results the power system increase reliability.

To really discover the power and ease in using the product, we recommend that

you read through this manual carefully.

1.2 PACKING

Your MyZx package should consist of the followings:

(A) MyZx series x 1

(B) Accessory pack x 1

Summary of content (10 pages)

PAGE 1
.1 INTRODUCTION First of all, thank you for purchasing MyZx series redundant power supply. The MyZx series is a N+1 hot-swappable / hot-pluggable redundant power supply. It consists of, The total output is up to your power’s requirements, you can figure out the total Power’s consumption and check over the specification, the you can find out the correct configuration. It delivers full safety redundant (hot-swappable) function and provides the hot-pluggable feature.
PAGE 2
1.
PAGE 3
8th --- attribute X --- P w/ PFC F w/ EMI filter 9th --- chassis type X --- H horizontal type V vertical type M horizontal + vertical type 10th --- Use FAN type X --- 3 use 3.
PAGE 4
1.4 FEATURES MyZx N+1, Hot-swap, Hot-plug, AC input min redundant power system l l l l l l l l l l l l l l l Low profile power module for building to the requirement N+1 power system design Current sharing design Remote sensing design 5 channels ( 5/12/-5/-12/3.3/5Vsb ) 350W /400W / 760W / 800W power module outputs Active power factor correction (PFC) built-in Universal AC power input Warning methods---LED, buzzer.
PAGE 5
PAGE 6
1.6 SPECIFICATIONS INPUT CHARACTERISTICS: l l l l l M1Z3-6760P3V / M1Z3-6800P3V VOLTAGE: 90V ~ 264VAC FREQUENCY: 47Hz ~ 63Hz INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE INRUSH CURRENT: 60/100A @ 115/230VAC (25℃) POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN. [A] MAX. [A] REGULATION LOAD LINE OUTPUT RIPPLE & NOISE MAX. [P-P] 5V 4.0 48 ± 5% ± 50mV 70mV 12V 5.0 50 ± 6% ± 50mV 120mV -5V 0.
PAGE 7
1.7 INSTALLATION & TESTING Mount the power system into the system chassis Attach the connectors to main board by following the main board’s instructions, there are various on pinouts / connectors in both the power system and main board, they should match each other, otherwise the connection will cause undetectable harms. Attach all the remaining power supply connections to the various peripherals as needed, these connectors maybe “keyed”, so there will be only one possible way to connect them.
PAGE 8
1.8 Hot-swap procedures Please refer to the following when one power module is found defective. (1) Locate the defective power module by examining the individual LED (if LED is without light, it indicates the power module is defective). WARNING: Please perform the BELOW step carefully; otherwise, it may cause shut down of the whole system. (2) Turn off WARNING: Please do not remove the defective power module until you have worn gloves to keep from been burned.
PAGE 9
1.9 PINOUTS AND FUNCTION OF THE CONNECTORS A. Power module defective signal: PIN# VOLTAGE SPECIFICATION 1 GND 2 TTL SIGNAL pull up to +5Vsb Low Active --- Defective High --- Normal B. Power status LED: PIN# VOLTAGE 1 GND 2 12V C. Buzzer reset switch: PIN# VOLTAGE 2 GND 1 5V SPECIFICATION Resistance 1K ohm to +12V Low Active(blink) --- Defective High (Green) --- Normal SPECIFICATION pull up to +5Vsb Low Active --- on shoot trigger TTL signal: Sink current max. 5mA Source current max.
PAGE 10
1.10 TROUBLE SHOOTING If you have followed all directions correctly, these should be no problem. Some common symptoms are: the system doesn’t work, buzzer sound, work for a very short period etc., please try the following steps to verify and correct it: 1. Check all the connections (correct pinouts, loose connection, wrong direction etc.,) 2. Check for short-circuit or defective peripherals by unhooking each peripheral once at a time. When the system functions again, you have solved the problem. 3.