User Manual

ManualsBrandsZippy ManualsAccessories for electricalR2G-5420P4V

1.1 INTRODUCTION

First of all, thank you for purchasing R1G series redundant power supply.

The R1G series is a N+1 hot-swappable / hot-pluggable redundant power supply. It

consists of,

1) complete metal frame

2) compact size power module

3) backplane

It is composed of N+1 pieces power modules. The number N+1 stands for there is an

extra power module to backup the system if any power module fails.

The power module is in compact size, and built-in a 40mm ball bearing DC fan.

Particularly, a 80mm DC fan is built unto the rear side of the power system to offer

better ventilation and reliability. Each power module is designed with 6 outputs (+3.3V,

+5V, +12V, -5V, -12V, and +5Vsb) circuits, and compliant to ATX12V / EPS12V. All you

can see on the backplane is just passive components and this is the key point for

longer MTBF.

The R2G/R3G series offer a warning sub-system, including LED display, buzzer alarm,

TTL signal, and I

C interface device (optional). It guides user the fast way to find out

the power supply and DC fan status.

When all the power modules operate normally, it balances the load share through its

parallel design, which increases the reliability of power system.

To really discover the power system and ease in using it, we recommend you to read

through this manual carefully.

Summary of content (12 pages)

PAGE 1
.1 INTRODUCTION First of all, thank you for purchasing R1G series redundant power supply. The R1G series is a N+1 hot-swappable / hot-pluggable redundant power supply. It consists of, 1) complete metal frame 2) compact size power module 3) backplane It is composed of N+1 pieces power modules. The number N+1 stands for there is an extra power module to backup the system if any power module fails. The power module is in compact size, and built-in a 40mm ball bearing DC fan.
PAGE 2
1.2 PACKING Your R1G series should consist of the following, a) R2G / R3G x 1 b) Accessory pack x 1 c) Product Manual x 1 1.3 MODEL DESINGATION Model number identification R2G / R3G -6zzzy R n 6 zzz y ----------- redundant the number of power module 6 output channel (+3.
PAGE 3
1.
PAGE 4
PAGE 5
PAGE 6
1.6 SPECIFICATION INPUT CHARACTERISTICS: R2G-6300P l VOLTAGE: 90 ~264 VAC FULL RANGE l FREQUENCY : 47 ~ 63 Hz l INPUT CURRENT: 6.0 / 3.0 A FOR 115 / 230 VAC l INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] ± 5% ± 1% 50mV ± 7% ± 1% 120mV 5V 3.0 32 12V 2 16 -5V 0.05 0.5 ± 10% ± 1% 120mV -12V 0.05 0.8 ± 10% ± 1% 150mV 3.
PAGE 7
INPUT CHARACTERISTICS: R2G-6350P l VOLTAGE: 90 ~ 264 VAC FULL RANGE l FREQUENCY : 47 ~ 63 Hz l INPUT CURRENT: 8.0 / 5.0 A FOR 115 / 230 VAC l INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] 5V 3.0 35 ± 5% ± 1% 50mV 12V 2 22 ± 5% ± 1% 100mV -5V 0.1 0.5 ± 10% ± 1% 150mV -12V 0.1 0.8 ± 10% ± 1% 150mV 3.3V 1.
PAGE 8
INPUT CHARACTERISTICS: R3G-6650P l VOLTAGE: 90 ~ 264 VAC FULL RANGE l FREQUENCY : 47 ~ 63 Hz l INPUT CURRENT: 9.0 / 5.0 A FOR 115 / 230 VAC l INRUSH CURRENT: 80A / 100A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] 5V 3.0 60 ± 5% ± 1% 50mV 12V 2 40 ± 5% ± 1% 100mV -5V 0.01 1 ± 10% ± 1% 150mV -12V 0.01 1 ± 10% ± 1% 150mV 3.3V 1.
PAGE 9
1.7 INSTALLATION & TESTING Mount the power supply into the system chassis by using proper mounting tool. The mounting holes of the power supply should match up with those in the chassis. Connect the power connectors to the M/B by following the M/B instruction. There is various on connectors / pinouts in both power supply and M/B. Please ensure to connect the matched one; otherwise, it will cause unexpected harms. Connect the remaining power connectors to the various peripherals as needed.
PAGE 10
1.8 Hot-swap procedures Please refer to the following when either power module is defective. 1) Locate the defective power module by examining the individual LED (if LED is distinguished, it indicates the power module is defective). *** WARNING: Please perform the following step carefully; otherwise, it may cause the whole system shutdown. *** WARNING: Please do not remove the defective power module until you have worn gloves to keep from been burned.
PAGE 11
1.9 PINOUTS AND FUNCTION OF THE CONNECTORS THE LED CONNECTOR OF TOTAL POWER SYSTEM PIN# 1 COLOR RED 2 BLACK 3 GREEN THE BUZZER RESET SWITCH CONNECTOR PIN# COLOR 1 2 BLACK YELLOW THE SIGNAL CONNECTOR OF POWER RESET PIN# COLOR COLOR 1 RED TTL SIGNAL 2 BLACK GND TTL signal: Sink current max. 5mA Source current max. 50uA Low Active ---Defective High ---Normal 1.10 TROUBLE SHOOTING If you have followed these instructions correctly, it should function normally.
PAGE 12
3) Once you hear the buzzer sound or see the warning LED become blinking, please check, a) If the loading is under the minimum or over the maximum load of each channel. b) If the power source is well connected and supplied. Shall the above condition is happened, please disconnect the power source and wait for 2-3 minutes to release the protection status; then test it again. c) If buzzer keeps alarming or LED indicates the power module failure, please locate which power module is defective.