Specification Sheet

ManualsBrands10Gtek ManualsComputers & AccessoriesColored 10G SFP+ DAC Cable - Twinax SFP Cable for Juniper QFX-SFP-DAC-3M/ EX-SFP-10GE-DAC-3M, 3-Meter(10ft)

Table Of Contents

SFP+ Passive Copper Cable Assembly

10Gtek Transceivers Co.,Ltd

Driving Your Next Generation Networks www.10gtek.com

E-mail:info@10gtek.com Tel: +86 755 2998 8100 Fax: +86 755 6162 4140

SFP+ Passive Copper Cable Assembly

CAB-10GSFP-PxM

Features

 SFF-8431 Compliant

 Broadband serial data rate operation:10 Mbps to 12 Gbps

 Power Level I: 15 mW per cable end

 100 Ohm differential impedance

 Retractable pin latch

 EEPROM signature

 Pull to Release latch design

 360°cable braid crimp

 Enhanced EMI skirt design

 Color options for strain relief and pull tab

 Linear design for use with EDCs

 AC-coupled inputs and outputs

 30AWG to 24AWG cable available

Applications

 10 Gigabit Ethernet and Gigabit

 Ethernet (IEEE 802.3ae)

 Fiber Channel: 1, 2, 4, 8, and 10GFC

 Infiniband SDR, DDR, and QDR

 Fiber Channel over Ethernet (FCoE)

 Serial data transmission

Summary of content (9 pages)

PAGE 1
0Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.
PAGE 2
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Product Description The passive SFP+ Direct attach copper cable assembly is a low cost alternative for short reach applications. The design allows for a serial data transmission up to 12Gbps in each direction. The passive design has no signal amplification in the cable assembly. Electronic Dispersion Compensation (EDC) is typically used on host board designs when passive copper cable assemblies are utilized.
PAGE 3
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com VMA and VCR Specifications VMA & VCR Cable Gauge Cable Length Spec Limit VMA (dB) -- VCR (dB) 4.5 30 AWG 3 meter 3.03875 28 AWG 5 meter 24 AWG 7 meter 3.93609 3.86154 33 40.6572 38.53281 37.
PAGE 4
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Host board Connector Pinout Figure 1s: MSA compliant Connector Figure 2s: Pin Definitions.
PAGE 5
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Note 3. This pin is an open collector/drain input pin and shall be pulled up with 4.7-10k to VccT in the module. Note 4. See 2-wire Electrical Specifications . Note 5. This pin shall be pulled up with 4.7-10k to Vcc_Host on the host board Pin Description Tx_Fault: Tx_Fault is an output pin to indicate a fault condition of a laser.This pin is connected to ground in the module.
PAGE 6
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.
PAGE 7
10Gtek Transceivers Co.
PAGE 8
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F www.10gtek.com 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Mechanical Specifications Mechanical Parameter Minimum Cable Diameter (24 AWG) Bend Radius (24 AWG) Inches 0.185 Inches 0.8 Inches 0.175 Inches 0.
PAGE 9
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Mechanical Dimensions Part Numbers Passive SFP+ Cable Assemblies Length 24AWG P/N 0.