User Guide

TRIP II
QUICK START GUIDE
BUTTON / INTERFACE POSITION
KEY FUNCTION
LIGHT INDICATORS
TURN ON AND TURN OFF
Power on: Press and hold the power button for more than 2
seconds to power on in shutdown state, and the white
indicator light flashes.
Shut down: Press and hold the power button for more than 2
seconds to shut down in power-on state, and the indicator
light off.
NOISE CANCELLATION SETTING
In the power-on state,double tap the touch panel to switch
Ambient Sound On/Noise Cancelling Off/Noise Cancelling On.
TOUCH FUNCTION
Tap: Play/Pause (Music) Answer(Call)
Double tap: Ambient Sound On/Noise Cancelling Off/
Noise Cancelling On switch
Triple tap: The Voice Assistant On
Press and hold 2S: Reject/End the call
VOICE PROMPTS
1. Power on: “Power on”
2. Pairing successful: “Audio connected”
3. Low battery: “Battery low”(<10%)
4. Bluetooth pairing: “Looking for device”
5. Connection disconnected：“Audio disconnected”
6. Power off: “Power off”
7. Maximum valume: “Beep Beep”
8. Incoming call when talking: “Beep Beep”
9. Hanging up: “Beep”
CALL FUNCTION
1. Tap the touch panel to answer the call.
2. Press and hold the touch panel for 2 seconds to reject the call.
WHEN THE CALL IS ACTIVE
1. Press and hold the touch panel for 2 seconds to hang up
the phone.
2. Press "Volume+" and "Volume -" to adjust the call volume.
CALL SWITCHING
1. Tap the panel to put the current caller on hold and connect
with the incoming call.
2. Long press the touch panel to continue the current call and
reject the new call.
3. While holding the call, tap the touch panel to hang up the
current caller.
Notice: Some of the mobile phone brands and models may
differ in operation. For queries contact sales for support.
CHARGING
1. When the battery power is less than 10%, the red indicator
light will flash with voice prompt.
2. While charging, the red indicator light is on.
3. When fully charged, the white indicator light is on.
Notice:
A. Charge the earphone via computer or certified
charger (output 5V/700mA and above), the earphone will
be fully charged in 3 hours.
B. If the earphone is automatically turned off due to
insufficient power, charge the earphone on time. If the
earphone is not charged for a long time, the battery life
may be affected.
PAIRING
Pair and connect for the first time
1. Press and hold the power button for 2 seconds in the
shutdown state, and the voice prompt "Power on" is
accompanied, the red and white lights flash alternately to
enter the pairing state, and the prompts "Looking for device".
2. Open the bluetooth on the mobile phone and find
"233621 TRIP II" to connect.
Turn On To Reconnect
Press and hold the power button for 2 seconds in the power-off
state, accompanied by a voice prompt of "Power on", white light
flashing, the headphone will reconnect to the recently connected
phone automatically.
Re-pair
1. Press and hold the power button for more than 5 seconds
to start up and enter the pairing state in the power-off state,
and prompt tone, red and white light flashing alternately.
2. In the power-on state, double-click the power button to
enter the pairing state, accompanied by a prompt tone,
red and white lights flash alternately.
3. Open the Bluetooth on the mobile phone to connect.
Disconnect and reconnect the Bluetooth
1. The headphone will not be powered off automatically when
ambient on or noise cancellation on.
2. Automatically powered off(In noise cancellation off):
After the headphone is disconnected and no reconnected
within 10 minutes, the headphone will turn off automatically.
Notice: The headphone will be powered off automatically
within 10 minutes, if there is no device connected to it. If there
is no mobile phone connection within 5 minutes when the
headphone is in the pairing state, the headphone will exit the
pairing state, and enter the connectable state with the white
light flashes. If there is still no mobile phone connection within
5 minutes, the headphone will be powered off automatically.
3. Remote disconnection and reconnection
(In noise cancellation off)
a. The headphone is disconnected, it will reconnect
automatically by returning valid connection range within
10 minutes.
b. After 10 minutes, the headphone will have to be manually
reconnected.
c. After 20 minutes of disconnection out the valid range, the
headphone will be powered off automatically.
Headphone x1
User guide x1Type-C charging cable x1
3.5mm audio port
Power/
Bluetooth pairing
Volume+/-
Type-C port
Touch Panel
Light
indicator
Tap: Play/Pause (Music) Answer(Call)
Double tap: Ambient Normal/Noise
Cancellation Off/Noise Cancellation On switch
Triple tap: The Voice Assistant On
Press and hold 2S: Reject/End the call
Short press increase volume
Long press next track
Short press decrease volume
Long press previous track
Press and Hold for 2 Seconds:
Power On/Power Off
Double Click: Enter Pairing Status
Disconnected (White light flashing)
Bluetooth pairing (Red & white light flashing)
Device connected (White light flashing)
Low battery (Red light flashing)
Charging (Red light on)
Charging complete (White light on)
PACKAGING LIST