Quick Start Guide

2
Copyright © 2020 Nortek Security & Control LLC
InstallEr toolbox
The Installer Toolbox is password-protected. To use this feature, you must enter an Installer Code. The factory default
code is 1561. To access the Installer Toolbox:
1. Tap the Settings icon ( ).
2. Tap KEYPAD.
3. Enter 1561 to gain access to the panel
settings, then tap Installer Toolbox.
4. Scroll down then tap the Installer
Toolbox icon.
5. Tap Panel Programming to view
programming options (see below).
PanEl ProgrammIng – WIrElEss ZonEs
Program up to 100 wireless zones per system. Tap Wireless Zones to view the Wireless Zones screen.
Setup a Wireless Zone
Left side of screen: Select a Wireless Zone [#].
Right side of screen: Tap and highlight each of
the available zones, then tap EDIT ZONE to view
settings for the selected zone.
PanEl ProgrammIng – buIlt-In ZonEs
You can program up to three (3) Built-In Zones per system. To get started, navigate to the Installer Toolbox.
Tap Panel Programming, then tap the Built-In Zones option.
Selecting a Built-In Zone
Left side of screen: Select a Wireled Zone [#].
Right side of screen: Tap and highlight each of the
available zones, then tap EDIT ZONE to view settings
for the selected zone.
PanEl ProgrammIng – KEyfobs
Program up to 32 keyfobs per system. To begin, navigate to the Installer Toolbox, then tap Panel Programming
then Keyfobs.
Select a Keyfob
Left side of screen: Select a Keyfob [#].
Right side of screen: Tap and highlight each of the
available zones, then tap EDIT ZONE to view settings
for the selected zone.
PanEl ProgrammIng – KEyPads
You can program up to eight (8) wireless keypads per system. To get started, navigate to the Installer Toolbox.
Then, tap Keypads. This reveals the Keypads screen.
Setup Keypad (#)
1. Swipe up to move through the list of keypads.
2. Tap to select one of the available keypads.
3. Tap Edit Keypad.
4. Make sure the Keypad Used setting is highlighted.
5. Under Keypad Used, choose Enabled or Disabled.
6. Tap t to move to the next option.
PanEl ProgrammIng – nEtWorK sEttIngs
Setup Wireless
1. Tap a available Network Name.
2. Correctly enter the assigned network password to
connect.
3. Tap  to go back to the Network Settings menu.
Setup the Access Point
1. Tap Network Settings.
2. Tap Access Point.
3. Enable Access Point:
â Optional: Tap to enter a new SSID name
â Optional: Tap to enter a new password
â Optional: Tap IP address. The last two octets of
the Access Point can be changed to customize
the setup.
4. If edits have been made, tap Save Settings to save.
Note: Make a note of SSID and Password for use in
WiFi setup of SP1 and SP2 keypads.
5. Tap  to go back to the Network Settings menu.
PanEl ProgrammIng – advancEd ProgrammIng
Tap Installer Toolbox, then tap Panel Programming > Advanced Programming > System Conguration.
System Conguration
Timers, Delays & Counts
Panel Conguration
Troubles
Reporting
1. Highlight a question [Q### - (settings differ based on the
question)].
2. Tap available options to adjust settings.
3. Tap  to move to the next question, or tap  to return to
the previous menu.
Note: Ensure that the settings you program are in
compliance with all national, state, and local regulations.
Note: For more in-depth information about the list of
questions available in the Panel Programming menu, refer
to the EDGE Installation & Programming Guide.
smart HomE sEttIngs
Add up to 232 Z-Wave devices to the network. After
adding or removing a device you should always
rediscover the network. Tap Settings, then Smart Home
Settings to view the Smart Home Settings menu.
View All Devices
Displays all Z-Wave Smart Home Devices connected to
the panel.
systEm tEst
After installing the system, sensors, and peripherals,
perform a walk test to ensure proper console
operations and to test wireless reception and signal
strength.
rEstorE dEfaults
If at any time you want to restore the system’s settings to the factory defaults.
1. Navigate to the Installer Toolbox.
2. Tap the Restore Defaults icon.
3. Tap to enable the Restore switch for the specic option(s).
4. Tap RESTORE.
10029907 Rev-X2